Roland INTEGRA-7

98
Chorus, Reverb
Chorus Parameters
The chorus section can be used as a delay.
Select either chorus or delay, and specify how the chorus/delay
sound will be heard.
Parameter Value Explanation
Chorus Type
00: OFF,
01: Chorus,
02: Delay,
03: GM2 Chorus
Selects either Chorus or Delay.
OFF: Neither Chorus or Delay is used.
Chorus: Chorus is used.
Delay: Delay is used.
GM2: GM2 Chorus is used.
Chorus Level 0–127 Volume of the chorus sound
Chorus Output
Assign
A, B, C, D
Selects the pair of OUTPUT jacks to
which the chorus sound is routed when
Chorus Output Select is set to “MAIN” or
“MAIN+REV.”
Chorus Output
Select
MAIN, REV,
MAIN+REV
Species how the sound routed through
chorus will be output.
MAIN: Output in stereo to the OUTPUT
jacks.
REV: Output in monaural to the reverb.
MAIN+REV: Output in stereo to the OUTPUT
jacks, and in monaural to the reverb.
01: Chorus
Filter Type OFF, LPF, HPF
Type of lter
OFF: No lter is used.
LPF: Cuts the frequency range above the
Cuto Freq
HPF: Cuts the frequency range below the
Cuto Freq
Cuto Freq 200–8000 [Hz] Basic frequency of the lter
Pre Delay 0.0–100 [msec]
Adjusts the delay time from the direct sound
until the chorus sound is heard.
Rate
0.05–10.00 [Hz],
note
Frequency of modulation
Depth 0–127 Depth of modulation
Phase 0–180 [deg] Spatial spread of the sound
Feedback 0–127
Adjusts the amount of the chorus sound
that is fed back into the eect.
02: Delay
Delay Left
0–1000 [msec],
note
Adjusts the delay time from the direct sound
until the delay sound is heard.
Delay Right
Delay Center
Center Feedback -98–+98 [%]
Adjusts the proportion of the delay sound
that is fed back into the eect. Negative “-”
settings will invert the phase.
HF Damp
200–8000 [Hz],
BYPASS
Adjusts the frequency above which sound
fed back to the eect will be cut. If you do
not want to cut the high frequencies, set this
parameter to BYPASS.
Left Level
0–127 Volume of each delay soundRight Level
Center Level
03: GM2 Chorus
Pre-LPF 0–7
Cuts the high frequency range of the sound
coming into the chorus.
Higher values will cut more of the high
frequencies.
Level 0–127 Volume of the chorus sound
Feedback 0–127
Adjusts the amount of the chorus sound
that is fed back into the eect.
Delay 0–127
Adjusts the delay time from the direct sound
until the chorus sound is heard.
Rate 0–127 Frequency of modulation
Depth 0–127 Depth of modulation
Parameter Value Explanation
Send Level to
Reverb
0–127
Adjusts the amount of chorus sound that
will be sent to the reverb.
Reverb Parameters
Parameter Value Explanation
Reverb Type
00: OFF
01: Room 1
02: Room 2
03: Hall 1
04: Hall 2
05: Plate
06: GM2 Reverb
Type of reverb
OFF: Reverb will not be used
Room 1/2: Reverb that simulates the
reverberation of a room
Hall 1/2: Reverb that simulates the
reverberation of a hall
Plate: Simulation of a plate echo (a reverb
device that uses a metal plate)
GM2 Reverb: GM2 reverb
Reverb Level 0–127 Volume of the reverb sound
Reverb Output
Assign
A, B, C, D
Species how the sound routed through
reverb will be output.
01–05: Room 1/2, Hall 1/2, Plate
Pre Delay 0–100 [msec]
Adjusts the delay time from the direct sound
until the reverb sound is heard.
Time 0.1–10 [sec] Time length of reverberation
Density 0–127 Density of reverb
Diusion 0–127
Adjusts the change in the density of the
reverb over time.
The higher the value, the more the density
increases with time.
(The eect of this setting is most
pronounced with long reverb times.)
LF Damp 0–100
Adjusts the low-frequency portion of the
reverb.
HF Damp 0–100
Adjusts the high-frequency portion of the
reverb.
Spread 0–127 Reverb spread
Tone 0–127 Tonal character of the reverb
06: GM2 Reverb
Character 0–5 Type of reverb
Time 0–127 Time length of reverberation