Roland INTEGRA-7

SuperNATURAL Drum Kit (SN-D) – COMP tab
40
Parameter Value Explanation
Output Assign PART, COMP+EQ1–6 Species for each drum inst how the sound will be output.
COMP tab
* COMP + EQ can be used only for the part specied by the Drum Comp+EQ Assign setting.
Comp 1–6 Switch OFF, ON Compressor on/o setting
Comp 1–6 Attack Time 0.05–50.0ms Time from when the input exceeds the threshold until compression begins
Comp 1–6 Release Time 0.05–2000ms Time from when the input falls below the threshold until compression is turned o
Comp 1–6 Threshold 0–127 Level above which compression is applied
Comp 1–6 Ratio 1:1–inf:1 Compression ratio
Comp 1–6 Output Gain 0–+24[dB] Level of the output sound
EQ tab
* COMP + EQ can be used only for the part specied by the Drum Comp+EQ Assign setting.
EQ 1–6 Switch OFF, ON Equalizer on/o setting
EQ1–6 Low Freq 200, 400 [Hz] Frequency of the low range
EQ1–6 Low Gain -15–+15 [dB] Gain of the low frequency range
EQ1–6 Mid Freq
200, 250, 315, 400, 500, 630, 800,
1000, 1250, 1600, 2000, 2500, 3150,
4000, 5000, 6300,8000 [Hz]
Frequency of the middle range
EQ1–6 Mid Gain -15–+15 [dB] Gain of the middle frequency range
EQ1–6 Mid Q 0.5, 1.0, 2.0, 4.0, 8.0
Width of the middle frequency range
Set a higher value for Q to narrow the range to be aected.
EQ1–6 High Freq 2000, 4000, 8000 [Hz] Frequency of the high range
EQ1–6 High Gain -15–+15 [dB] Gain of the high frequency range
MFX tab
MFX Switch OFF, ON Switches the multi-eect (MFX) on/o.
MFX Type 0–67
Use this parameter to select from among the 67 available MFXs. For details on MFX parameters,
refer to “MFX Parameters” (p. 73).
Parameters for each MFX type Make parameter settings for the selected MFX type.
MFX Chorus Send Level 0–127
Adjusts the amount of chorus for the sound that passes through multi-eects. If you don’t want to
add the Chorus eect, set it to “0.”
* This has no eect if motional surround is on.
MFX Reverb Send Level 0–127
Adjusts the amount of reverb for the sound that passes through multi-eects. If you don’t want to
add the Reverb eect, set it to “0.”
* This has no eect if motional surround is on.
MFX CTRL tab
Source (1–4)
OFF, CC01–31, 33–95, PITCH BEND,
AFTERTOUCH, SYS CTRL1–SYS CTRL4
Sets the MIDI message used to change the multi-eects parameter with the multi-eects control.
OFF: Multi-eects control will not be used.
CC01–31, 33–95: Control Change
PITCH BEND: Pitch Bend
AFTERTOUCH: Aftertouch
SYS CTRL1–SYS CTRL4: MIDI messages used as common multi-eects controls.
Destination (1–4)
Sets the multi-eects parameters to be controlled with the multi-eects control. The multi-eects parameters available for control will
depend on the multi-eects type. For details, refer to “MFX Parameter” (p. 97).
Sens (1–4) -63–+63
Sets the amount of the multi-eects control’s eect that is applied.
To make an increase in the currently selected value (to get higher values, move to the right,
increase rates, and so on), select a positive value; to make a decrease in the currently selected value
(to get lower values, move to the left, decrease rates, and so on), select a negative value.
For either positive or negative settings, greater absolute values will allow greater amounts of
change. Set this to “0” if you don’t want to apply the eect.