Roland INTEGRA-7

87
MFX Parameters
40: Time Ctrl Delay
A stereo delay in which the delay time can be varied smoothly.
R in
R out
L in
L out
Feedback
Feedback
Balance W
Balance W
Time Ctrl Delay
Time Ctrl Delay
2-Band EQ
2-Band EQ
Balance D
Balance D
Parameter Value Explanation
Delay Time # 0–1300 ms, note
Adjusts the time until the delay is
heard.
Acceleration 0–15
Adjusts the speed which the Delay
Time changes from the current
setting to a specied new setting.
The rate of change for the Delay Time
directly aects the rate of pitch change.
Feedback # -98–+98 %
Adjusts the amount of the delay
that’s fed back into the eect.
Negative “-” settings invert the
phase.
HF Damp
200–8000 Hz,
BYPASS
Adjusts the frequency above which
sound fed back to the eect is
ltered out. If you do not want to
lter out any high frequencies, set
this parameter to BYPASS.
Low Gain -15–+15 dB Gain of the low frequency range
High Gain -15–+15 dB Gain of the high frequency range
Balance #
D100:0W
–D0:100W
Volume balance between the direct
sound (D) and the delay sound (W)
Level 0–127 Output Level
41: LOFI Compress
This is an eect that intentionally degrades the sound quality for
creative purposes.
L in
R in
L out
R out
Compressor
Lo-Fi
Lo-Fi
Compressor
2-Band
EQ
2-Band
EQ
Parameter Value Explanation
Pre Filt Type 1–6
Selects the type of lter applied to
the sound before it passes through
the Lo-Fi eect.
1: Compressor o
2–6: Compressor on
LoFi Type 1–9
Degrades the sound quality. The
sound quality grows poorer as this
value is increased.
PostFilt Type OFF, LPF, HPF
Type of lter
OFF: no lter is used
LPF: cuts the frequency range above
the Cuto
HPF: cuts the frequency range
below the Cuto
PostFilt Cof 200–8000 Hz Basic frequency of the Post Filter
Low Gain -15–+15 dB Gain of the low range
High Gain -15–+15 dB Gain of the high range
Balance #
D100:0W
–D0:100W
Volume balance between the direct
sound (D) and the eect sound (W)
Level # 0–127 Output Level
42: Bit Crasher
This creates a lo- sound.
L in
R in
L out
R out
Bit Crasher
2-Band EQ
2-Band EQ
Bit Crasher
Parameter Value Explanation
Sample Rate # 0–127 Adjusts the sample rate.
Bit Down # 0–20 Adjusts the bit depth.
Filter # 0–127 Adjusts the lter depth.
Low Gain -15–+15 dB Gain of the low frequency range
High Gain -15–+15 dB Gain of the high frequency range
Level 0–127 Output Level
43: Pitch Shifter
A stereo pitch shifter.
L in
R in
Pitch Shifter
Pitch Shifter
L out
R out
2-Band EQ
2-Band EQ
Parameter Value Explanation
Coarse #1 -24–+12 semi
Adjusts the pitch of the pitch shifted
sound in semitone steps.
Fine #1 -100–+100 cent
Adjusts the pitch of the pitch shifted
sound in 2-cent steps.
Delay Time 0–1300 ms, note
Adjusts the delay time from the
direct sound until the pitch shifted
sound is heard.
Feedback # -98–+98 %
Adjusts the proportion of the pitch
shifted sound that is fed back into
the eect. Negative “-” settings will
invert the phase.
Low Gain -15–+15 dB Gain of the low range
High Gain -15–+15 dB Gain of the high range
Balance #
D100:0W
–D0:100W
Volume balance between the direct
sound (D) and the pitch shifted
sound (W)
Level 0–127 Output Level