Roland INTEGRA-7

SuperNATURAL Synth Tone (SN-S) – MOD LFO tab
37
Parameter Value Explanation
MOD LFO tab
ModLFO Shape
Selects the MODULATION LFO waveform.
There is an LFO that is always applied to the partial, and a MODULATION LFO for applying modulation when the pitch bend/modulation
lever is moved away from yourself.
TRI
Triangle wave
SIN
Sine wave
SAW
Sawtooth wave
SQR
Square wave
S&H Sample and Hold (The LFO value will change once each cycle.)
RND Random wave
ModLFO Rate 0–127 Species the LFO rate when Modulation LFO Tempo Sync Switch is OFF.
ModLFO TempoSyncSw OFF, ON If this is ON, the LFO rate can be specied as a note value relative to the tempo.
ModLFO TempoSyncNote
16, 12, 8, 4, 2, 1, 3/4, 2/3, 1/2, 3/8, 1/3,
1/4, 3/16, 1/6, 1/8, 3/32, 1/12, 1/16,
1/24, 1/32
Species the LFO rate when Modulation LFO Tempo Sync Switch is ON.
ModLFO Pitch Depth -63–+63 This allows the LFO to modulate the pitch, producing a vibrato eect.
ModLFO FILTER Depth -63–+63 This allows the LFO to modulate the FILTER CUTOFF (cuto frequency), producing a wah eect.
ModLFO AMP Depth -63–+63 This allows the LFO to modulate the AMP LEVEL (volume), producing a tremolo eect.
ModLFO Pan Depth -63–+63 Here’s how to make the PAN (stereo position) vary (Auto Panning).
ModLFO Rate Control -63–+63
Make these settings if you want to change the Modulation LFO Rate when the modulation lever is
operated.
Specify a positive “+” value if you want the Modulation LFO Rate to speed up when you move the
modulation lever; specify a negative “-” value if you want it to slow down.
AFTERTOUCH tab
Cuto Aftertouch Sens -63–+63
Species how aftertouch pressure will aect the cuto frequency.
Specify a positive “+” value if you want aftertouch to raise the cuto frequency; specify a negative
“-” value if you want aftertouch to lower the cuto frequency.
Level Aftertouch Sens -63–+63
Species how aftertouch pressure will aect the volume.
Specify a positive “+” value if you want aftertouch to increase the volume; specify a negative “-”
value if you want aftertouch to decrease the volume.
MISC tab
Attack Time Interval Sens 0–127
Shortens the FILTER and AMP Attack Time according to the spacing between note-on events.
Higher values produce a greater eect. With a setting of 0, there will be no eect. This is eective
when you want to play rapid notes using a sound that has a slow attack (Attack Time).
Release Time Interval Sens 0–127
Shortens the FILTER and AMP Release Time if the interval between one note-on and the next
note-o is brief. Higher values produce a greater eect. With a setting of 0, there will be no eect.
This is eective when you want to play staccato notes using a sound that has a slow release.
Portamento Time Interval Sens 0–127
Shortens the Portamento Time according to the spacing between note-on events. Higher values
produce a greater eect. With a setting of 0, there will be no eect.
Envelope Loop Mode
Use this to loop the envelope between certain regions during a note-on.
Decay
Attack
Sustain
OFF The envelope will operate normally.
FREE-RUN
When the Decay segment has ended, the envelope will return to the Attack. The Attack through
Decay segments will repeat until note-o occurs.
TEMPO-SYNC Species the loop rate as a note value (Sync Note parameter).
Envelope Loop Sync Note Note (p. 96)
Returns to the Attack at the specied rate. If the Attack+Decay time is shorter than the specied
rate, the Sustain Level will be maintained. If the Attack+Decay time is longer than the specied
rate, the envelope will return to the Attack even though the Decay has not been completed.
This will continue repeating until note-o occurs.
Chromatic Portamento OFF, ON If this is turned on, portamento will operate in semitone steps.