Roland INTEGRA-7

PCM Drum Kit (PCMD) – WAVE tab
67
Parameter Value Explanation
Partial Rx Hold-1 OFF, ON
For each drum partial, specify whether MIDI Hold-1 messages will be received (ON), or not (OFF).
NOTE
If “NO-SUS” is selected for Partial Env Mode parameter (p. 66), this setting will have no eect.
One Shot Mode OFF, ON
The sound will play back until the end of the waveform (or the end of the envelope, whichever
comes rst).
The result will be the same as when the envelope’s Partial Env Mode parameter is set to “NO-SUS.”
WAVE tab
Wave 1–4 Switch OFF, ON Turns the wave on/o.
Wave Group
INT,
SRX
(only if an expansion is loaded)
Select the groups containing the Waves comprising the drum partial.
INT: Waveforms stored in internal
SRX: Expansion sound banks
Wave No.L (Mono)
OFF, 1–
This selects the Waves comprising the drum partial. Along with the Wave number, the Wave name
appears at the lower part of the display.
When in monaural mode, only the left side (L) is specied. When in stereo, the right side (R) is also
specied.
Wave No.R
Wave Gain -6, 0, +6, +12 [dB]
Sets the gain (amplication) of the waveform.
The value changes in 6 dB (decibel) steps—an increase of 6 dB doubles the waveform’s gain.
Wave Tempo Sync OFF, ON
When you wish to synchronize a Phrase Loop to the clock (tempo), set this to “ON.”
This is valid only when an SRX waveform which indicates a tempo (BPM) is selected.
(Example: SRX05 3:080:BladeBtL, SRX08 5:75:BoomRvBel, etc.)
If a waveform from an SRX is selected for the partial, turning the Wave Tempo Sync parameter
“ON” will cause pitch-related settings and FXM-related settings to be ignored.
Phrase Loop
“Phrase Loop” refers to the repeated playback of a phrase that’s been pulled out of a song
(e.g., by using a sampler). One technique involving the use of Phrase Loops is the excerpting
of a Phrase from a pre-existing song in a certain genre, for example dance music, and then
creating a new song with that Phrase used as the basic motif. This is referred to as “Break
Beats.”
Wave FXM Switch OFF, ON
This sets whether FXM will be used (ON) or not (OFF).
FXM
FXM (Frequency Cross Modulation) uses a specied waveform to apply frequency modulation
to the currently selected waveform, creating complex overtones. This is useful for creating
dramatic sounds or sound eects.
Wave FXM Color 1–4
Species how FXM will perform frequency modulation.
Higher settings result in a grainier sound, while lower settings result in a more metallic sound.
Wave FXM Depth 0–16
Species the depth of the modulation produced by FXM.
NOTE
When the Tempo Sync is set to “ON,” settings related to Pitch (p. 68) and FXM are disabled.
Wave Coarse Tune -48–+48
Adjusts the pitch of the waveform’s sound up or down in semitone steps (+/-4 octaves).
MEMO
The Coarse Tune of the entire drum partial is set by the Partial Coarse Tune (p. 68).
Wave Fine Tune -50–+50
Adjusts the pitch of the waveform’s sound up or down in 1-cent steps (+/-50 cents).
* One cent is 1/100th of a semitone.
MEMO
The Fine Tune of the entire drum partial is set by the Partial Fine Tune (p. 68).
Wave Level 0–127
You can set the volume of the waveform.
MEMO
The volume level of each drum partial is set with the Partial Level; the volume levels of the
entire drum kit is set with the Drum Kit Level (p. 66*).
Wave Pan L64–63R
This species the pan of the waveform.
“L64” is far left, “0” is center, and “63R” is far right.
Wave Random Pan Sw OFF, ON
Use this setting to cause the waveform’s panning to change randomly each time a key is pressed
(ON) or not (OFF).
* The range of the panning change is set by the Random Pan Depth (p. 71).
Wave Alter Pan Sw OFF, ON, REVS
This setting causes panning of the waveform to be alternated between left and right each time a
key is pressed. Set Alter Pan Sw to “ON” to pan the Wave according to the Alter Pan Depth settings,
or to “REVS” when you want the panning reversed. If you do not want the panning to change each
time a key is pressed, set this to “OFF.”