Roland Jupiter-50 - MISC ([F6] button); LIVE SET;TONE BUTTONS

The JUPITER-50’s System Settings
78
MISC ([F6] button)
Parameter Value Explanation
Metronome
Metronome Level 0–10 Species the metronome volume.
Metronome Sound TYPE1–TYPE4 Species the metronome type.
System Control Source
System Control 1–4
Source
Here you can specify the MIDI messages that will be used as
system controls.
System controls 1–4 are parameters to which you can assign
MIDI messages such as control change messages.
For example, on the JUPITER-50, if you choose a system
control as the MFX CONTROL Source (LIVE SET EFFECT
screen; p. 58), you’ll be able to use MIDI messages to control
eect parameters.
It is convenient to use system controls when you don’t need
to use dierent MIDI messages for MFX CONTROL of each
Live Set, or if you want to use a specic MIDI message for
MFX CONTROL.
SuperNATURAL Acoustic Tones can be controlled using the
MIDI messages that you’ve assigned to system controls 1
and 2, allowing you to produce eects such as vibrato or
dynamics (for some tones there will be no change).
OFF System control will not be used.
CC01–31, CC32
(OFF), 33–95
Controller 1–95
PITCH BEND Pitch Bend
AFTERTOUCH Aftertouch
Startup Registration
Startup Registra-
tion
[00] ---,
[01] 1-1–[08] 4-4
Species the Registration that will be
selected when you turn on the power.
Manual Registration
Registration
Manual Button
MANUAL,
SINGLE
Species whether pressing the
[MANUAL] button will select Manual or
Single Part Play.
Live Set 0001–2560
Species the Live Set that will be
selected when you press the [MANUAL]
button.
Screen Saver
Screen Saver Time
OFF,
1–60 [min]
Species the time (minutes) until the
screen saver is activated.
If this is OFF, the screen saver will not
operate.
Auto O
Auto O OFF, 30, 240 [min]
With the factory settings, the
JUPITER-50’s power will automatically
be switched o 4 hours after you stop
playing or operating the unit (factory
setting).
If you don’t want the power to turn
o automatically, set the “Auto O”
parameter to “OFF” (p. 79).
Visual Control
Visual Control
Mode
MVC
Control a device compatible with MIDI
Visual Control.
V-LINK Control a device compatible with V-LINK.
USB Driver
USB Driver
VENDER
(MIDI+AUDIO)
The dedicated JUPITER-50 driver
provided by Roland will be used.
MIDI and audio will be available.
GENERIC
(MIDI only)
The generic driver provided by the
operating system will be used.
Only MIDI will be available.
LIVE SET/TONE BUTTONS
Here you can specify the sounds (Live Sets or tones) that will be
assigned to the Part sound buttons (Upper, Percussion/Lower, Solo).
MEMO
The sounds you specify here will be saved as system parameters
(settings for the entire JUPITER-50). If you specify sounds within
a Registration, the Registration settings will take priority.
REFERENCE
• “Using the Part Sound Buttons to Switch Live Sets” (p. 40)
• “Using the Part Sound Buttons to Switch the Solo Part’s Tone”
(p. 41)
• “Instantly Switching the Variation Sounds (Alternate Button)”
(p. 42)
Parameter Explanation
SOLO
Species the sounds that will be assigned to the Solo Part sound
buttons.
SOLO Alternate
Species the sounds that will be assigned to the sound buttons
when the Solo Part [ALTERNATE] button is pressed.
UPPER
Species the sounds that will be assigned to the Upper Part
sound buttons.
UPPER Alternate
Species the sounds that will be assigned to the sound buttons
when the Upper Part [ALTERNATE] button is pressed.
PERCUSSION
Species the sounds that will be assigned to the Percussion Part
sound buttons.
LOWER
Species the sounds that will be assigned to the Lower Part
sound buttons.
INFORMATION
Here you can view information such as the JUPITER-50’s software
version and the amount of free space available on the USB ash
drive.
VERSION
Shows the JUPITER-50’s software version.
USB MEM
Shows the amount of free space available on the USB ash drive.