Roland Jupiter-50 - Page 90

Parameter List
90
0048:Harp, 0093:APS Harp
By turning Glissando mode (CC19) on, you can cause only the notes included in a
specic scale to be sounded.
This lets you easily produce an idiomatic harp glissando simply by playing a glissando
on the white keys.
It is eective to play this while holding down the HOLD pedal.
By using Mute (CC18) you can simulate the technique of using your hand to stop the
vibration of the strings.
Parameter Value Explanation
Glissando Mode
(CC19)
OFF, ON
If this is on, you can produce the eect
of sweeping across the harp strings by
playing a glissando on the keyboard.
Play Scale
7th, Major, Minor,
Hrm-Mi
(Harmonic
Minor), Dim
(Diminish),
Whole (Whole
Tone)
Species the scale used when
Glissando Mode is on.
Scale Key
C, Db, D, Eb, E, F,
Gb, G, Ab, A, Bb, B
Species the key of the scale produced
when you play a glissando with
Glissando Mode turned on.
Variation Refer to p. 98 Performance variation sounds
0049:Timpani, 0094:APS Timpani
You can play a roll by operating the Modulation controller (CC01) while playing a
note.
You can use Mute (CC18) to simulate the muting technique of using your hand to
press down on the timpani.
It is eective to assign this to the D-BEAM controller.
Parameter Value Explanation
Roll Speed (CC17) -64– +63 Adjusts the speed of the roll eect.
Variation Refer to p. 98 Performance variation sounds
0050:Strings, 0095:APS Strings
Parameter Value Explanation
Variation Refer to p. 98 Performance variation sounds
0051:Trumpet, 0052:Flugel Horn, 0056:Mute
Trumpet, 0057:French Horn, 0096:APS
Trumpet, 0098:APS Mute Trumpet, 0099:APS
French Horn
By setting Bend Range to Tone, you can use the pitch bend lever to create discontinu-
ous pitch changes or falls that are typical of a brass instrument.
• Moving the pitch bend lever in the upward direction will create a discontinuous
pitch change typical of brass instruments.
• Moving the pitch bend lever in the downward direction will produce a fall eect.
If Bend Range is set to anything other than Tone, this eect will be produced if Bend
Mode (CC19) is turned on. Use this when you want to switch between discontinuous
pitch changes or falls, and conventional pitch change.
Parameter Value Explanation
Noise Level (CC16) -64– +63
Adjusts the amount of breath noise for
the brass instrument.
Growl Sens (CC18) 0–127
Adjusts the distinctive nuance (growl)
that occurs when a brass instrument
is blown.
Variation Refer to p. 98 Performance variation sounds
0053:Trombone–0055:Bass Trombone,
0097:APS Trombone
By playing legato with the Portamento SW turned on, you can create the eect of
glissando performance on a trombone.
By setting Bend Range to Tone, you can use the pitch bend lever to create discontinu-
ous pitch changes or falls that are typical of a brass instrument.
• Moving the pitch bend lever in the upward direction will create a discontinuous
pitch change typical of brass instruments.
• Moving the pitch bend lever in the downward direction will produce a fall eect.
If Bend Range is set to anything other than Tone, this eect will be produced if Bend
Mode (CC19) is turned on. Use this when you want to switch between discontinuous
pitch changes or falls, and conventional pitch change.
Parameter Value Explanation
Noise Level (CC16) -64– +63
Adjusts the amount of breath noise for
the brass instrument.
Growl Sens (CC18) 0–127
Adjusts the distinctive nuance (growl)
that occurs when a brass instrument
is blown.
Variation Refer to p. 98 Performance variation sounds
0058:Soprano Sax–0061:Baritone Sax,
0100:APS Soprano Sax–0103:APS Baritone Sax
If Bend Range is set to Tone, you can use the pitch bend lever to create glissando or
fall eects.
• Moving the pitch bend lever in the upward direction will produce a glissando
eect.
• Moving the pitch bend lever in the downward direction will produce a fall eect.
If Bend Range is set to anything other than Tone, this eect will be produced if Bend
Mode (CC19) is turned on. Use this when you want to switch between glissando/fall
eects and conventional pitch change.
Parameter Value Explanation
Noise Level (CC16) -64– +63
Adjusts the amount of the brass
instrument’s breath noise or key noise.
Growl Sens (CC18) 0–127
Adjusts the distinctive nuance (growl)
that occurs when a brass instrument
is blown.
Variation Refer to p. 98 Performance variation sounds
0062:Oboe–0069:Flute 2, 0104:APS Oboe–
0109:APS Flute
If Bend Range is set to Tone, you can use the pitch bend lever to create glissando or
fall eects.
• Moving the pitch bend lever in the upward direction will produce a glissando
eect.
• Moving the pitch bend lever in the downward direction will produce a fall eect.
If Bend Range is set to anything other than Tone, this eect will be produced if Bend
Mode (CC19) is turned on. Use this when you want to switch between glissando/fall
eects and conventional pitch change.
Parameter Value Explanation
Noise Level (CC16) -64– +63
Adjusts the amount of breath noise for
the brass instrument.
Growl Sens (CC18) 0–127
Adjusts the distinctive nuance (growl)
that occurs when a brass instrument
is blown.
Variation Refer to p. 98 Performance variation sounds