Roland Jupiter-50 - Page 97

Parameter List
97
Introduction Playing Sounds Editing Sounds
Other Convenient
Functions
Connecting Other
Equipment
Appendix
Quick Guide
SuperNATURAL
Acoustic Tone
CC16 CC17 CC18 CC19 CC80 CC81 CC82 CC83
SuperNATURAL
Acoustic Tone
CC65 CC76
CC01 (System Control 1
Source) *1
AFTERTOUCH
(System Control 2
Source) *2
0104 APS Oboe Noise Level – Growl Sens Bend Mode (*8) Staccato – – – 0104 APS Oboe Portamento – Dynamics+Vibrato Vibrato
0105 APS English Horn Noise Level – Growl Sens Bend Mode (*8) Staccato – – – 0105 APS English Horn Portamento – Dynamics+Vibrato Vibrato
0106 APS Bassoon Noise Level – Growl Sens Bend Mode (*8) Staccato – – – 0106 APS Bassoon Portamento – Dynamics+Vibrato Vibrato
0107 APS Clarinet Noise Level – Growl Sens Bend Mode (*8) Staccato – – – 0107 APS Clarinet Portamento – Dynamics+Vibrato Vibrato
0108 APS Piccolo Noise Level – Growl Sens Bend Mode (*8) Staccato – – – 0108 APS Piccolo Portamento – Dynamics+Vibrato Vibrato
0109 APS Flute Noise Level – Growl Sens Bend Mode (*8) Staccato – – – 0109 APS Flute Portamento – Dynamics+Vibrato Vibrato
0110 APS Pan Flute Noise Level – Growl Sens Bend Mode (*8) Staccato Flutter – –
0110 APS Pan Flute Portamento – Dynamics+Vibrato Vibrato
0111 APS Shakuhachi Noise Level – Growl Sens – Staccato Ornament – – 0111 APS Shakuhachi Portamento – Dynamics+Vibrato Vibrato
0112 APS Ryuteki Noise Level – Growl Sens – Staccato Ornament – – 0112 APS Ryuteki Portamento – Dynamics+Vibrato Vibrato
0113 APS Sitar Resonance Level – – – Tambura (*10) – – – 0113 APS Sitar Portamento – Vibrato Vibrato
0114 APS UilleannPipe – – – – Drone (*10) Ornament – – 0114 APS UilleannPipe Portamento – Dynamics Vibrato
0115 APS Erhu Noise Level – – – Staccato Ornament – – 0115 APS Erhu Portamento – Dynamics+Vibrato Vibrato
0116 APS Sarangi Resonance Level – – – Tambura (*10) – – – 0116 APS Sarangi Portamento – Dynamics Vibrato
0117 APS Steel Drums Resonance Level Roll Speed Mute (*4) Bend Mode (*9) Mute – – – 0117 APS Steel Drums Portamento – Roll Sw+Dynamics (*3) –
*1 The setting of System Control 1 Source is used. With the factory settings, CC01 is assigned.
*2 The setting of System Control 2 Source is used. With the factory settings, AFTERTOUCH is assigned.
*3 Regardless of the System Control 1 Source setting, this can always be controlled by CC01.
*4 Mute: Simulates the technique of using a hand or mallet to stop the vibration (sound) of the instrument. Higher values will produce stronger muting.
*5 Mute: Simulates the technique of using a hand to stop the vibration of the string.
*6 Bend Mode: If Bend Range is set to anything other than Tone, operating the pitch bend lever when Bend Mode (CC19) is ON will produce a bellows tremolo eect.
Use this if you want to switch between the tremolo eect and conventional pitch change.
*7 Bend Mode: If Bend Range is set to anything other than Tone, operating the pitch bend lever when Bend Mode (CC19) is ON will simulate the wah eect produced
by cupping the hands around the instrument. Use this when you want to switch between the wah eect and conventional pitch change.
*8 Bend Mode: If Bend Range is set to anything other than Tone, operating the pitch bend lever when Bend Mode (CC19) is ON will produce a discontinuous pitch
change. Use this if you want to switch between discontinuous pitch change and conventional pitch change.
*9 Bend Mode: If Bend Range is set to anything other than Tone, operating the pitch bend lever when Bend Mode (CC19) is ON will produce a glissando eect. Use this
if you want to switch between glissando playing and conventional pitch change.
*10 The sound of the corresponding technique will be produced.