Roland V-Synth GT - Advanced (When Phrase Model Is Multifade)

136
Editing a Tone (Pro Edit)
Com MOD COSM1/2 TVAOSC1/2 AP Syn EffectsCom MOD COSM1/2 TVAOSC1/2 AP Syn Effects
fig.06b-75-ps.eps_50
Advanced (when Phrase Model is “Multifade”)
Parameter
Value Description
Brightness
-2– +2
Adjusts the brightness of the sound (five steps). Positive (+) values will
brighten the sound, and negative (-) values will darken it.
Porta Depth (Portamento Depth) -100– +100
Adjusts the amount of pitch change produced by portamento. Positive
(+) values will increase the amount of pitch change, and negative (-) val-
ues will decrease it.
Fade1 Ctl Default
(Fade 1 Control Default)
-100– +100
Adjusts the initial tone balance for fade 1 immediately after the sound
is selected (before you operate a controller).
* This may not work for some selections of Source Waveform.
Fade2 Ctl Default
(Fade 2 Control Default)
-100– +100
Adjusts the initial tone balance for fade 2 immediately after the sound
is selected (before you operate a controller).
* This may not work for some selections of Source Waveform.
Low Velo Limit
(Low Velocity Limit)
-100– +100
Adjusts the lower limit of the dynamics produced by the force of your
keyboard playing. Positive (+) values will increase the lower limit value,
and negative (-) values will decrease it.
* This may not work for some selections of Source Waveform.
Low Dyn Ctrl Lmt
(Low Dynamics Controller Limit)
-100– +100
Adjusts the lower limit of the dynamics produced when you operate the
controller assigned to dynamics. Positive (+) values will increase the low-
er limit value, and negative (-) values will decrease it.
* This may not work for some selections of Source Waveform.
Vibrato Dyn Sens
(Vibrato Dynamics Sensitivity)
-100– +100
Adjusts the linkage between changes in dynamics and changes in vibra-
to depth. Positive (+) values will produce deeper vibrato, and negative
(-) values will produce less vibrato.
Vibrato Reac Tm
(Vibrato Reaction Time)
-100– +100
Adjusts the reaction time when you control the vibrato using the control-
ler assigned to vibrato. Positive (+) values will make the response slow-
er, and negative (-) values will make the response quicker.
Fade Ctrl Reac Tm
(Fade Controller Reaction Time)
-100– +100
Adjusts the reaction time when you modify the tone by operating the
controllers assigned to fade 1 and 2. Positive (+) values will make the
response slower, and negative (-) values will make the response quicker.
* This may not work for some selections of Source Waveform.
PitchBend Reac Tm
(Pitch Bend Reaction Time)
-100– +100
Adjusts the reaction time when you operate the pitch bender to control
the pitch. Positive (+) values will make the response slower, and nega-
tive (-) values will make the response quicker.
Dyn Ctrl1 Reac Tm
(Dynamics Controller 1 Reaction
Time)
-100– +100
Adjusts the reaction time when you control the dynamics using the con-
troller assigned to dynamics. Positive (+) values will make the response
slower, and negative (-) values will make the response quicker.
* This may not work for some selections of Source Waveform.
Dyn Ctrl2 Reac Tm
(Dynamics Controller 2 Reaction
Time)
-100– +100
Adjusts the reaction time when you control the dynamics using the con-
troller assigned to dynamics. Positive (+) values will make the response
slower, and negative (-) values will make the response quicker.
* This may not work for some selections of Source Waveform.
Ambience Level -100– +100
Adjusts the amount of ambience. Positive (+) values will increase the
amount of ambience, and negative (-) values will decrease it.
V-Synth-GT_e.book 136 ページ ２００７年４月９日 月曜日 午後１時４６分