SharkRF openSPOT3 - NXDN Transceiver

CrossmodesusinganNXDN®transceiver
UsingaDMRnetwork
Afteryou'vesetupandactivatedtheDMRconnector,switchthemodemtoNXDN®mode.
ThesourceDMRIDofyourNXDN®callswillbesettothesamevalueastheNXDN®callunlesstheAlwaysuse
thisIDincrossmodesettingisenabledfortheDefaultcrossmodesourceIDontheSettingspage,NXDN®
settingssection.
YourNXDN®callswillbesenttothesameDMRIDastheNXDN®call'sdestinationIDunlesstheAlwaysusethis
IDincrossmodesettingisenabledfortheDefaultcrossmodedestinationIDontheSettingspage,NXDN®
settingssection.
ThedestinationandsourceNXDN®IDsforanincomingDMRcallwillbesettothesamevalueastheincoming
call'sdestinationandsourceIDunlesstheAlwaysusethisIDincrossmodesettingisenabledforthe
destination/sourceNXDN®IDsontheSettingspage,NXDN®settingssection(oriftheincomingDMRcall's
destinationorsourceIDisoutoftheNXDN®IDrange(0-65535)).
PrivateDMRcallsareconvertedtoNXDN®groupcalls.
UsingaD-STAR®network
Afteryou'vesetupandactivatedtheD-STAR®connector,switchthemodemtoNXDN®mode.
YouroutgoingcallsignwillbethecallsignassociatedwiththeNXDN®sourceID.Ifthere'snocallsignassociated
totheID,thenthecallsignwillbetheDefaultcallsignforcrossmodecalls.Ifthisisnotset,youroutgoing
callsignwillbeyourradio'sNXDN®IDastext.
Anincomingcall'ssourceNXDN®IDwillbesettotheIDassociatedwiththesourcecallsign.Ifthere'snoID
associated,andthesourcecallsigncanbeparsedintoanumber,itwillbeusedasthesourceNXDN®ID.
OtherwisetheDefaultcrossmodesourceIDwillbeused.
AllcallscomingfromtheD-STAR®networkwillbesentasagroupcalltotheDefaultcrossmodedestinationID.
Ifyoudon'thearcallsonyourradiothenmakesurethisIDisintheselectivecalllist(orSelCallisturnedoff),or
it'stheTXcontactofthecurrentchannel.
UsingaC4FMnetwork
Afteryou'vesetupandactivatedtheC4FMconnector,switchthemodemtoNXDN®mode.OnlycallsinDN
(DigitalNarrow)modewillbeconvertedtoyourNXDN®radio.IfsomeonetransmitsinothermodesontheC4FM
network,youwillhearsilenceonyourNXDN®radio.
YouroutgoingcallsignwillbethecallsignassociatedwiththeNXDN®sourceID.Ifthere'snocallsignassociated
totheID,thenthecallsignwillbetheDefaultcallsignforcrossmodecalls.Ifthisisnotset,youroutgoing
callsignwillbeyourradio'sNXDN®IDastext.
Anincomingcall'ssourceNXDN®IDwillbesettotheIDassociatedwiththesourcecallsign.Ifthere'snoID
associated,andthesourcecallsigncanbeparsedintoanumber,itwillbeusedasthesourceNXDN®ID.
OtherwisetheDefaultcrossmodesourceIDwillbeused.
AllcallscomingfromtheC4FMnetworkwillbesentasagroupcalltotheDefaultcrossmodedestinationID.If
youdon'thearcallsonyourradiothenmakesurethisIDisintheselectivecalllist(orSelCallisturnedoff),or
it'stheTXcontactofthecurrentchannel.
NXDN®transceiver
112