SharkRF openSPOT3 - NXDN Settings; P25 Settings

code,theoutgoingcalltothenetworkwillbeautomaticallyended,sootherswon'tbeannoyedbyhearing
yourDTMFtonesonthesamereflector/talkgroup.
Specialcommand/crossmodeprivatecallDTMFcode:thiscodeisusedasthefirstcharacterforenteringa
controlDTMFcode,orstartingaprivatecallincrossmodes.Seemoreinfoateachconnector'sdescription,or
attheControlcallssection.
CrossmodegroupcallDTMFcode:ifaconnectorisactivewhichsupportsgroupcallsandC4FMcrossmode,
thenthiscodecanbeusedtostartgroupcallstotheIDenteredafterthiscode.
IfTransmitRXconfirmationischecked,thentheopenSPOT3willtransmitashortcallconfirmationafterthe
PTTisreleasedontheC4FMradio.
IfacallisreceivedbythemodemtotheEchoDGID,thentheopenSPOT3'sbuilt-inlocalechoservicegets
activated.Itwillrecordthecallandplaysitbackafterthecallisfinished.
IftheOnlyreceiveDGIDfrommodemcheckboxischecked,thencallsonlytothespecifiedDGIDfrom
modemwillbeprocessedbythemodem.
IftheReplaceDGIDtomodemenabledcheckboxischecked,thentheDGIDinallframesreceivedfromthe
networkwillbereplacedwiththespecifiedReplaceDGIDtomodemvalue.
IftheReplaceDGIDtonetenabledcheckboxischecked,thentheDGIDinallframesreceivedfromthe
modemwillbereplacedwiththespecifiedReplaceDGIDtonetvalue.
NXDN®settings
ThemodemwillonlyprocessNXDN®callswithamatchingRadioAccessNumberifitissetotherthan0.
IfacalliscomingfromamodewhichdoesnothaveIDinformation(ex.C4FM),orthesourceIDisoutside
theNXDN®IDrange(0-65535),thentheDefaultcrossmodesourceIDwillbeusedasthesourceIDforthe
call.ThisIDwillalwaysbeusediftheAlwaysusethisIDincrossmodecheckboxischecked.
Ifyouuseanon-NXDN®networkwithyourNXDN®radio,youcansetthistoyourNXDN®ID.
IfAdvancedmodeisenabled,thefollowingsettingsshowup:
IfacallisreceivedbythemodemtotheEchoID,thentheopenSPOT3'sbuilt-inlocalechoservicegets
activated.Itwillrecordthecallandplaysitbackafterthecallisfinished.Bothprivateandgroupcallsare
answeredwithaprivateechocallreply.
IfacalliscomingfromamodewhichdoesnothaveIDinformation(ex.C4FM),orthedestinationIDis
outsidetheNXDN®IDrange(0-65535),thentheDefaultcrossmodedestinationIDwillbeusedasthe
destinationIDforthecall.ThisIDwillalwaysbeusediftheAlwaysusethisIDincrossmodecheckboxis
checked.
IftheAllowonlyIDsascrossmodecallsignssettingisenabled,andthesourcecallsignofacrossmodecall
hasnoassociatedIDinthedatabase,andalsoitcan'tbeparsedintoanNXDN®ID,thenthecallwillbe
ignored.
P25settings
Settingspage
56