SharkRF openSPOT3 - Page 79

ID0,oracallsign-basedmodemmodeisused(likeD-STAR®andC4FM).
YoucanalsoupdatetheRoutecrossmodecallstoIDwiththeQuickcallfeature.
Ifthecurrentlyusedmodemmodeiscallsign-based(likeD-STAR®andC4FM),thenyoucanuseDTMFcodes
(seebelow)toupdatetheRoutecrossmodecallstoIDsetting.IftheUnlinkTG/ref.oncrossmodeDTMFcall
settingisenabled(itisenabledbydefault),thentheopenSPOT3willautomaticallydoaquickgroupcalltoDMR
ID4000beforecallingthenewID,tomakesureonlyonetalkgroupislinkedatatime.
D-STAR®notes
YoucanupdatetheRoutecrossmodecallstoIDwithaD-STAR®radiousingtwomethods:
SettheIDandcalltypeintheD-STAR®radio'sURCALL,thenstartashortcall.Aftertheshortcall,setback
theURCALLto CQCQCQ.Examples:
2161005P-privatecallto2161005
216G-groupcallto216
216-groupcallto216(ifthere'sno Gcharacterthenthecalltypeissettogroupcall)
DTMFcodes:youcanstartashortprivatecalltoanIDbyentering*followedbythedestinationIDinDTMF
code.YoucanstartashortgroupcalltoanIDbyentering#followedbythedestinationIDinDTMFcode.
Examples:
#3100-groupcallto3100
*4770-privatecallto4770
YoucanswitchserversusingtheURCALL/yourcallmethod.Thisletsyouchangetothefollowingservertypes:
REF/XRX/Gateway:settheURCALLtoforexample REF001C.SwitchingtoREF/XRFserversorgatewaysthis
waychangestheopenSPOT3'sactiveconnectortotheREF/XRFconnector.
DCS/XLX:settheURCALLtoforexample DCS001A.SwitchingtoDCS/XLXserversthiswaychangesthe
openSPOT3'sactiveconnectortotheDCS/XLXconnector.
BrandMeister:settheURCALLto BMfollowedbytheBrandMeisterserverID.Example:startingacallto
destinationcallsign(URCALL) BM2162switchestoBrandMeisterserver2162(Hungary).Switchingto
BrandMeisterserversthiswaychangestheopenSPOT3'sactiveconnectortotheHomebrew/MMDVM
connector.
FCS:settheURCALLtotheFCSserverandroomnumber.Example:startingacalltodestinationcallsign
(URCALL) FCS00199switchestoFCS001room99.SwitchingtoFCSserversthiswaychangesthe
openSPOT3'sactiveconnectortotheFCSconnector.
YSFReflector:settheURCALLto YSfollowedbytheYSFReflectorserverID.Example:startingacallto
destinationcallsign(URCALL) YS89804switchestoYSFReflector89804(AmericaLink).Switchingto
YSFReflectorserversthiswaychangestheopenSPOT3'sactiveconnectortotheYSFReflectorconnector.
NXDNReflector:settheURCALLto NXfollowedbytheNXDNReflectorserverID.Example:startingacallto
destinationcallsign(URCALL) NX28299switchestoNXDNReflector28299(America-Ragchew).Switchingto
NXDNReflectorserversthiswaychangestheopenSPOT3'sactiveconnectortotheNXDNReflectorconnector.
C4FMnotes
IfyouuseaC4FMradio,makesureitisindigitalnarrow(DN)mode,otherwiseyourcallscan'tbeconvertedand
onlysilencewillbesenttothenetwork.
YoucanupdatetheRoutecrossmodecallstoIDwithaC4FMradiousingDTMFcodes.Youcanstartashort
privatecalltoanIDbyenteringtheSpecialcommand/crossmodeprivatecallDTMFcode(bydefaultit's*)
followedbythedestinationIDinDTMFcode.YoucanstartashortgroupcalltoanIDbyenteringtheCrossmode
groupcallDTMFcode]followedbythedestinationIDinDTMFcode.
Homebrew/MMDVM®
79