3.16.2.6 Read curve table values (CTABTSV, CTABTEV, CTABTSP, CTABTEP, CTABSSV,
CTABSEV, CTAB, CTABINV, CTABTMIN, CTABTMAX) ....................................................905
3.16.2.7 Curve tables: Check use of resources (CTABNO, CTABNOMEM, CTABFNO,
CTABSEGID, CTABSEG, CTABFSEG, CTABMSEG, CTABPOLID, CTABPOL,
CTABFPOL, CTABMPOL) ...................................................................................................910
3.16.3 Axial master value coupling (LEADON, LEADOF)...............................................................911
3.16.4 Electronic gear (EG).............................................................................................................917
3.16.4.1 Defining an electronic gear (EGDEF)...................................................................................917
3.16.4.2 Switch-in the electronic gearbox (EGON, EGONSYN, EGONSYNE)..................................918
3.16.4.3 Switching-in the electronic gearbox (EGOFS, EGOFC).......................................................921
3.16.4.4 Deleting the definition of an electronic gear (EGDEL) .........................................................922
3.16.4.5 Rotational feedrate (G95) / electronic gear (FPR) ...............................................................922
3.16.5 Synchronous spindle............................................................................................................923
3.16.5.1 Synchronous spindle: Programming (COUPDEF, COUPDEL, COUPON, COUPONC,
COUPOF, COUPOFS, COUPRES, WAITC) .......................................................................923
3.16.6 Generic coupling (CP...).......................................................................................................933
3.16.7 Tangential control.................................................................................................................940
3.16.7.1 Defining coupling (TANG) ....................................................................................................940
3.16.7.2 Activating intermediate block generation (TLIFT) ................................................................942
3.16.7.3 Activating the coupling (TANGON) ......................................................................................943
3.16.7.4 Deactivating the coupling (TANGOF)...................................................................................945
3.16.7.5 Deleting a coupling (TANGDEL) ..........................................................................................945
3.16.8 Master/slave coupling (MASLDEF, MASLDEL, MASLON, MASLOF, MASLOFS) ..............947
3.17 Synchronized actions ...........................................................................................................950
3.17.1 Definition of a synchronized action ......................................................................................950
3.18 Oscillation.............................................................................................................................951
3.18.1 Asynchronous oscillation (OS, OSP1, OSP2, OST1, OST2, OSCTRL, OSNSC, OSE,
OSB) ....................................................................................................................................951
3.18.2 Oscillation controlled by synchronized actions (OSCILL) ....................................................955
3.19 Punching and nibbling..........................................................................................................963
3.19.1 Activation/deactivation .........................................................................................................963
3.19.1.1 Activate/deactivate punching and nibbling (SPOF, SON, PON, SONS, PONS,
PDELAYON, PDELAYOF, PUNCHACC).............................................................................963
3.19.2 Automatic path segmentation...............................................................................................968
3.19.2.1 Path segmentation for path axes .........................................................................................970
3.19.2.2 Path segmentation for single axes .......................................................................................972
3.20 Grinding................................................................................................................................974
3.20.1 Activate/deactivate grinding-specific tool monitoring (TMON, TMOF) .................................974
3.21 Extended stop and retract (ESR) .........................................................................................975
3.21.1 NC-controlled ESR...............................................................................................................976
3.21.1.1 NC-controlled retraction (POLF, POLFA, POLFMASK, POLFMLIN) ...................................976
3.21.1.2 NC-controlled stopping.........................................................................................................979
3.21.2 Drive-integrated ESR ...........................................................................................................980
3.21.2.1 Configuring drive-integrated stopping (ESRS) .....................................................................980
3.21.2.2 Configuring drive-integrated retraction (ESRS)....................................................................981
3.22 Program runtime/part counter ..............................................................................................983
3.22.1 Program runtime ..................................................................................................................983
3.22.2 Workpiece counter ...............................................................................................................986
3.23 Additional functions ..............................................................................................................988
Table of contents
NC programming
Programming Manual, 12/2019, 6FC5398-2EP40-0BA0 17
To Next Page
Loading...
Need help?
General
