3.25.1.33 CYCLE782 - adjust to load.................................................................................................1091
3.25.1.34 CYCLE800 – swivel plane / swivel tool / align tool.............................................................1094
3.25.1.35 CYCLE801 – grid or frame position pattern .......................................................................1097
3.25.1.36 CYCLE802 - arbitrary positions..........................................................................................1099
3.25.1.37 CYCLE830 - deep-hole drilling 2........................................................................................1101
3.25.1.38 CYCLE832 - High-Speed Settings .....................................................................................1107
3.25.1.39 CYCLE840 - tapping with compensating chuck .................................................................1110
3.25.1.40 CYCLE899 – open slot.......................................................................................................1113
3.25.1.41 CYCLE930 - groove ...........................................................................................................1116
3.25.1.42 CYCLE940 – undercut form E and F / undercut thread .....................................................1118
3.25.1.43 CYCLE951 - stock removal................................................................................................1121
3.25.1.44 CYCLE952 – stock removal / residual stock removal / plunge cutting / residual plunge
cutting / plunge turning / residual plunge turning ...............................................................1124
3.25.1.45 CYCLE4071 - longitudinal grinding with infeed at the reversal point .................................1130
3.25.1.46 CYCLE4072 - longitudinal grinding with infeed at the reversal point and cancel signal ....1132
3.25.1.47 CYCLE4073 - longitudinal grinding with continuous infeed ...............................................1136
3.25.1.48 CYCLE4074 - longitudinal grinding with continuous infeed and cancel signal...................1137
3.25.1.49 CYCLE4075 - surface grinding with infeed at the reversal point........................................1140
3.25.1.50 CYCLE4077 - surface grinding with infeed at the reversal point and cancel signal...........1143
3.25.1.51 CYCLE4078 - surface grinding with continuous infeed......................................................1147
3.25.1.52 CYCLE4079 - surface grinding with intermittent infeed .....................................................1149
3.25.1.53 GROUP_BEGIN - beginning of program block ..................................................................1152
3.25.1.54 GROUP_END - end of program block................................................................................1152
3.25.1.55 GROUP_ADDEND - End of trial cut addition .....................................................................1153
3.25.1.56 Supplementary conditions..................................................................................................1153
3.25.2 Measuring cycles ...............................................................................................................1154
3.25.3 Overview of measuring cycle parameters ..........................................................................1155
3.25.3.1 CYCLE973 measuring cycle parameters ...........................................................................1155
3.25.3.2 CYCLE974 measuring cycle parameters ...........................................................................1158
3.25.3.3 CYCLE994 measuring cycle parameters ...........................................................................1160
3.25.3.4 CYCLE976 measuring cycle parameters ...........................................................................1163
3.25.3.5 CYCLE978 measuring cycle parameters ...........................................................................1165
3.25.3.6 CYCLE998 measuring cycle parameters ...........................................................................1168
3.25.3.7 CYCLE977 measuring cycle parameters ...........................................................................1171
3.25.3.8 CYCLE961 measuring cycle parameters ...........................................................................1175
3.25.3.9 CYCLE979 measuring cycle parameters ...........................................................................1177
3.25.3.10 CYCLE997 measuring cycle parameters ...........................................................................1180
3.25.3.11 CYCLE995 measuring cycle parameters ...........................................................................1183
3.25.3.12 CYCLE996 measuring cycle parameters ...........................................................................1184
3.25.3.13 CYCLE9960 measuring cycle parameters .........................................................................1187
3.25.3.14 CYCLE982 measuring cycle parameters ...........................................................................1189
3.25.3.15 CYCLE971 measuring cycle parameters ...........................................................................1191
3.25.3.16 CYCLE150 measuring cycle parameters ...........................................................................1194
4 Tables.....................................................................................................................................................1197
4.1 Operations..........................................................................................................................1197
4.2 Addresses ..........................................................................................................................1235
4.2.1 Address letters ...................................................................................................................1235
4.2.2 Fixed addresses.................................................................................................................1236
4.2.3 Settable addresses ............................................................................................................1240
4.3 G commands......................................................................................................................1247
Table of contents
NC programming
Programming Manual, 12/2019, 6FC5398-2EP40-0BA0 19
To Next Page
Loading...
Need help?
General
