How to fix rudder feedback failure on Simrad AP35?
If your Simrad Autopilot System shows a rudder feedback failure and operates on simulated feedback, it means the rudder feedback signal is missing or erratic. First, check all connections and ensure they are secure. Then, check the alignment according to the installation instructions. If the problem persists, you may need to replace the rudder feedback unit.
What to do if compass data is missing on Simrad AP35 Autopilot System?
If your Simrad Autopilot System is showing that compass data is missing, it indicates that there is no data from the selected compass. If you have multiple compasses connected, go to the USER SETUP menu and select a different compass. Also, check the connections and the Interface menu settings. If the problem continues, consider replacing the compass PCB or interface PCB, remembering not to cut any cables as the PCB contains screw terminals.
General| Brand | Simrad |
|---|---|
| Model | AP35 |
| Category | Autopilot System |
| Language | English |
Overview of the Simrad AP35 autopilot system and its advantages.
Guidance on navigating and understanding the content of the instruction manual.
Details the essential units that form a basic AP35 autopilot system.
Description of the compact autopilot control unit for panel, bulkhead, or bracket mounting.
Information on the central steering computer and interface circuits for AP35 system modules.
Details on RF300 and RF45X units for transforming rudder angle to digital signals.
Overview of compatible heading sensors like RFC35 and RC25 compasses.
Information on additional accessories available to expand the AP35 system's functionality.
Introduction to the AP35 control unit's operation and steering modes.
Procedure for turning the AP35 system ON/OFF and entering Standby mode.
How to activate and use Follow-Up steering mode for rudder control.
Explanation of Non-Follow-Up steering activated by separate PORT or STBD buttons.
Operation of the NFU steering lever for rudder control.
How to use the NFU push button remote for steering.
Instructions for operating the R3000X handheld remote control.
Details on using the S35 NFU steering lever for mode and course changes.
How to engage AUTO mode for automatic steering on a set heading.
Explanation of HI/LO speed steering parameters and automatic selection.
Procedure for manually selecting HI or LO speed steering parameters.
Using the AP35 for navigation to waypoints with external navigator input.
Guidance on choosing navigation sources within the AP35 system.
How to use the WORK mode for specific operational conditions like trawling or towing.
Description of U-Turn and C-Turn features for changing course.
Using the Dodging function for evasive maneuvers and returning to course.
Managing control and active/inactive states in a multistation AP35 system.
How to use the LOCK function to disable all control units except one.
Navigating and adjusting settings within the AP35 User Set-up Menu.
Technical details of the AP35 autopilot system, including boat size, steering types, and connectivity.
Specifications for the AP35 control unit, including dimensions, display, and environmental protection.
Technical data for J300X, J300X-40, and J3000X junction units, including voltage and capacity.
Specifications for the RFC35 fluxgate compass, covering dimensions and performance.
Technical details for the RC25 Rate Compass, including its integrated rate of turn sensor.
Specifications for the CDI35 interface unit and CD100A course detector.
Technical data for the RI35 Mk2 rudder angle indicator, including dimensions and accuracy.
Specifications for the RF300 rudder feedback unit and its transmission link.
Technical details for the RF45X rudder feedback unit and transmission link.
Specifications for the R3000X handheld remote control.
Technical data for the CI300X compass interface, covering gyro and magnetic compass inputs.
Specifications for the NI300X NMEA interface unit, including NMEA ports and data output.
Technical details for the S35 NFU steering lever, including inductive load and protection.
Specifications for the F1/2 handheld remote control.
Technical data for the FU50 follow-up steering lever, including rudder command angle.
Explanation of IP protection codes used for Simrad autopilot system components.
Overview of the installation process for the AP35 autopilot system.
A step-by-step checklist to ensure all installation requirements are met.
Guidelines for safely unpacking and handling AP35 system components.
Importance of understanding system configuration before beginning installation.
Diagram illustrating the AP35 basic system layout with various options.
Instructions for mounting and connecting the RF300 rudder feedback unit.
Steps for mounting and connecting the RF45X rudder feedback unit.
Information on mounting and connecting the AP35 system's junction unit.
Details on connecting various drive units to the AP35 system.
Instructions for mounting the AP35 control unit, including panel and bracket options.
Guidance on mounting and connecting the RFC35 fluxgate compass.
Instructions for connecting the RC25 Rate Compass to the AP35 control unit.
Details on mounting and connecting the R3000X remote control.
Reference to the FU50 manual for connecting the FU50 steering lever.
Instructions for connecting the S35 NFU steering lever to the junction unit.
How to connect the F1/2 handheld remote control to the AP35 system.
Instructions for mounting and connecting the RI35 Mk2 rudder angle indicator.
Options for connecting other equipment to the AP35 for data exchange.
Diagram for connecting a single NMEA device to the AP35 system.
Diagram for connecting multiple NMEA devices to the AP35 system.
Configuring additional NMEA output on Port 2 of the AP35 system.
Connecting an NMEA compass to the J300X/J300X-40 junction unit.
Connecting radar clock/data interface to the J300X junction unit.
Connecting IS15 instruments for speed and depth input to the autopilot.
Diagram for connecting AR77 and AR68 analog repeaters to the AP35 system.
Diagram for connecting the DR75 digital repeater to the AP35 system.
Connecting an external alarm relay or buzzer to the AP35 system.
Installation of the NI300X NMEA interface for expanding NMEA connectivity.
Connecting various analogue equipment using the CI300X interface unit.
Instructions for mounting and connecting the CD100A course detector.
Guidance on locating and connecting the CDI35 interface to the compass.
Steps for configuring the AP35 system's software settings.
Procedures for performing sea trial settings like rudder zero adjust and compass calibration.
Guidance for conducting a final sea trial to test autopilot performance.
Key operational functions to cover when training the end-user.
Maintenance recommendations for the AP35 Control Unit, focusing on cleaning and connections.
No special maintenance required for the junction unit; visual inspection advised.
Visual inspection of rudder feedback unit at intervals and lubrication of ball joints.
Visual inspection of the compass, especially if exposed to weather.
Refer to the drive unit manual for specific maintenance instructions.
Procedure for removing and installing EPROMs for software updates.
Information on PCB modifications and compatibility for AP35 control units.
Troubleshooting common system failure alarms and probable faults.
Using the NMEA Test Menu to check NMEA message status and data validity.
Accessing system data for testing and troubleshooting, including NMEA hardware test.
To Next Page
