Synrad FH FLYER - Page 250

index
i8
SYNRAD FH Series Flyer Operator’s Manual Version 3.4
Trademark information xv
Troubleshooting
automation I/O, 6-16–6-17
FH Flyer, 6-9–6-14
indicator LEDs, 6-8–6-9
Laser Marking FAQ, 6-17
stand-alone mode, 6-14
tracking mode, 6-15–6-16
USB Port, 5-25
U
UID/Composite Codes 3-3
Unpacking 1-4
Upgrading
rmware, 5-32
Upload Current Mark File button 3-6
Usable Field Size 4-4, 4-8, 4-25, 4-28
denition, 4-3
USB Communication cable 1-6, 1-16, 1-17,
1-21, 2-2, 5-25, 6-11
connecting, 1-16–1-17
USB indicator 1-17, 2-2, 6-9
USB Port 1-16, 1-17, 2-2, 2-5, 3-20, 3-23
connection, 5-25
electrical isolation, 5-25
electrical noise, 5-25
Use Control File 3-16, 3-18, 3-21, 3-24
property, 3-4
Use DHCP
property, 1-21, 1-23
Use Quadrature Encoder
property, 4-22
User Interface connection 1-17, 2-2, 3-18,
3-20, 3-21, 3-23, 4-10, 4-14, 4-22,
5-5, 5-6, 5-8, 5-18, 5-19, 5-20, 5-21,
5-23, 5-24, 5-35, 6-17
caution, 5-5
connector layout, 5-5
overview, 5-5–5-6
pin assignments, 5-6, 5-7, 5-8
V
Velocity 4-28, 5-37
W
Warning
air contaminants, 2
denition, 1
immediate marking, 2-7, 3-5, 3-17
laser safety precautions, 2
radiation exposure, 2
WaitDigitalState 5-38, 5-39
Warranty information xvi
Web interface 5-31
WinMark control mode 1-3, 2-5–2-7, 3-2
WinMark Pro Hardlock 1-19, 3-5, 3-6, 3-7,
3-8, 3-11, 3-12
WinMark Pro software 1-2, 1-3, 1-12, 1-16,
1-17, 1-19, 1-20, 1-21, 2-5, 2-6, 3-2,
3-4, 3-5, 3-6, 3-7, 3-8, 3-10, 3-11,
3-12, 3-13, 3-14, 3-15, 3-16, 3-17,
3-18, 3-19, 3-20, 3-21, 3-23, 3-24,
4-12, 4-17, 4-19, 4-22, 4-28, 5-3, 5-4,
5-25, 5-26, 5-31, 5-32, 5-33, 5-34,
5-35, 5-36, 5-37, 5-38, 5-39, 6-9,
6-11, 6-12, 6-13, 6-14, 6-15, A-2, A-4,
B-2
Digital Scope, 4-11, 4-16, 5-35, 6-15,
6-17, B-2, B-3, B-4
Drawing Canvas, 2-6, 3-5, 3-6, 3-7, 4-3,
4-6, 4-8, 4-13, 4-19, 4-20, 4-21, 4-22,
4-26, 4-27, 4-28, 5-4, 6-13, 6-15
Drawing Editor 3-5, 3-7, 3-10, 4-12, 4-19
system requirements, 1-19
tracking setup, 4-19–4-23
WinMark/Flyer conguration, 1-19–1-20
WinMark/Flyer interface, 3-4–3-15
WinMark Launcher, 2-7, 3-17, 3-19, 3-20,
3-23, 3-24, 5-34
WinMark Pro User Guide, 1-19, 3-18, 3-21,
5-5
Working distance 1-8
typical specications, 5-4
measurement, 2-3, 2-7, 3-17, 3-19, 3-22,
6-13
Z
Z-axis adjustment 1-2, 1-8, 2-3, 2-7, 3-17,
3-19, 3-22, 4-2, 4-13, 6-13, C-2