EasyManuals Logo

Texas Instruments MSP430 series User Manual

Texas Instruments MSP430 series
191 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #7 background imageLoading...
Page #7 background image
This manual describes the hardware of the TI MSP-FET430 Flash Emulation Tool (FET). The FET is the
program development tool for the MSP430
ultra-low-power microcontrollers.
How to Use This Manual
Read and follow the instructions in Chapter 1. This section lists the contents of the FET and provides instructions
on installing the hardware and the software drivers. After you see how quick and easy it is to use the
development tools, TI recommends that you read all of this manual.
This manual describes the setup and operation of the FET but does not fully describe the MSP430
microcontrollers or the development software systems. For details of these items, see the appropriate TI
documents listed in Section 1.17.
This manual applies to the following tools:
MSP-FET430PIF – debug interface with parallel port connection, for all MSP430 flash-based devices
MSP-FET430UIF – debug interface with USB connection, for all MSP430 flash-based devices
MSP-FET – successor to MSP-FET430UIF, debug interface with USB connection, for all MSP430 devices
eZ430-F2013 – USB stick form factor interface with attached MSP430F2013 target, for all MSP430F20xx,
MSP430G2x01, MSP430G2x11, MSP430G2x21, and MSP430G2x31 devices
eZ430-T2012 – three MSP430F2012 based target boards
eZ430-RF2500 – USB stick form factor interface with attached MSP430F2274 and CC2500 target, for all
MSP430F20xx, MSP430F21x2, MSP430F22xx, MSP430G2x01, MSP430G2x11, MSP430G2x21, and
MSP430G2x31 devices
eZ430-RF2500T – one MSP430F2274 and CC2500 target board including battery pack)
eZ430-RF2500-SEH – USB stick form factor interface with attached MSP430F2274 and CC2500 target and
solar energy harvesting module
eZ430-Chronos-xxx – USB stick form factor interface with CC430F6137 based development system
contained in a watch; includes <1 GHz RF USB access point
Stand-alone target-socket modules without debug interface are named as MSP-TS430TSxx.
Tools named as MSP-FET430Uxx contain the USB debug interface (MSP-FET430UIF) and the respective target
socket module MSP-TS430TSxx, where 'xx' is the same for both names. The following tools contain also the
USB debug interface (MSP-FET430UIF):
FET430F5137RF900 – for CC430F513x devices in 48-pin RGZ packages (green PCB)
FET430F6137RF900 – for CC430F612x and CC430F613x devices in 64-pin RGC packages (green PCB)
These tools contain the most up-to-date materials available at the time of packaging. For the latest materials
(data sheets, user's guides, software, application information, and so on), visit the TI MSP430 website or contact
your local TI sales office.
Preface
Read This First
www.ti.com Read This First
SLAU278AG – MAY 2009 – REVISED DECEMBER 2020
Submit Document Feedback
MSP430™ Hardware Tools 7
Copyright © 2020 Texas Instruments Incorporated

Table of Contents

Other manuals for Texas Instruments MSP430 series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Texas Instruments MSP430 series and is the answer not in the manual?

Texas Instruments MSP430 series Specifications

General IconGeneral
BrandTexas Instruments
ModelMSP430 series
CategoryMicrocontrollers
LanguageEnglish

Related product manuals