Toshiba e-STUDIO477SL - Page 406

e-STUDIO477S/527S
05/08
Mode
Element
Sub Element
Item
Subitem
Code
Sub-
Code
Details
Default
value
Acceptable
value
RAM
Contents
Proc
edure
ServiceUI
08
Job handling-short paid-
coin controller
Sets whether pause or stop the printing job when it
is short paid using a coin controller.
0: Pause the job
1: Stop the job
2: Stop the job immediately
It is recommended to select "2" (Stop the job
immediately) when you want to set "stop" while the
multiple numbers of USB direct printing is
performed. (To shorten of hours)
Setting
mode
System
User interface
Counter installed
externally
9037
1
0~2
1
SYS
08
Operating mode 1
For plain paper, thick 1, LG. For non-sort mode
and sort mode. Do not change this setting unless
otherwise instructed.
0: Disabled 1: Enabled
Setting
mode
System
Finisher
Finisher tray
operating mode
9048
0
0
0~1
4
SYS
08
Operating mode 2
For thick 2. Do not change this setting unless
otherwise instructed.
0: Disabled 1: Enabled
Setting
mode
System
Finisher
Finisher tray
operating mode
9048
1
0
0~1
4
SYS
08
Operating mode 3
For thick 3. Do not change this setting unless
otherwise instructed.
0: Disabled 1: Enabled
Setting
mode
System
Finisher
Finisher tray
operating mode
9048
2
0
0~1
4
SYS
08
Operating mode 4
For thick 4. Do not change this setting unless
otherwise instructed.
0: Disabled 1: Enabled
Setting
mode
System
Finisher
Finisher tray
operating mode
9048
3
0
0~1
4
SYS
08
Operating mode 5
For LG. For Single-sided stapling. Do not change
this setting unless otherwise instructed.
0: Disabled 1: Enabled
Setting
mode
System
Finisher
Finisher tray
operating mode
9048
4
0
0~1
4
SYS
08
Operating mode 6
For single-sided stapling. Do not change this
setting unless otherwise instructed.
0: Disabled 1: Enabled
Setting
mode
System
Finisher
Finisher tray
operating mode
9048
5
0
0~1
4
SYS
08
Scanning operating mode
Do not change this setting unless otherwise
instructed.
0: Operating mode 1
1: Operating mode 2
Setting
mode
System
Scanning
9049
0
0~1
1
SYS
08
Performing panel calibration
Performs the calibration of the pressing position on
the touch panel (LCD screen).
The calibration is performed by pressing 4
reference positions after this code is started up.
Setting
mode
System
Maintenance
General
9050
1
Yes
SYS
08
Panel calibration setting
value
Switches whether the screen for displaying panel
calibration setting values is displayed or not.
0: Disabled (screen not displayed)
1: Enabled (screen displayed)
Setting
mode
System
User interface
Display setting
9051
0
0~1
1
Yes
SYS
08
Destination display at
SRAM initialization
0: MJD 1: NAD 2: JPD 3: AUD 4: Not defined 5:
Not defined 6: Not defined 7: Not defined 8: Not
defined 9: Not defined 10: ARD 11: Not defined
<Default value>
JPD: 2 NAD: 1 MJD: 0 AUD: 3 ARD: 10
Setting
mode
System
9060
Refer to
contents
0~255
2
SYS
08
HDD diagnostic menu
display
Displays the HDD information.
Setting
mode
System
HDD
9065
2
Yes
SYS
08
Performing HDD testing
Checks the bad sector. It may take more than 30
minutes to finish the checking.
Setting
mode
System
HDD
9072
3
SYS
53
Ver03
08 Setting Mode