Wayne 4310 - AC Drive Level; Figure 4-23 AC Drive Level Setting; Figure 4-24 AC Drive Level Setting

96 pages

Save Page as PDF

To Next Page

To Previous Page

Operation 4–19

4.4.11 AC Drive Level

When Drive Level has been selected from the Set Pull Down Menu (or using the Level Soft

Key), the following page will be displayed:

Figure 4-23 AC Drive Level Setting Page 1

stage

When the first digit of the required level has been keyed in, the soft keys will change, as shown

below, to allow the required voltage units to be selected with a single keystroke.

Figure 4-24 AC Drive Level Setting Page 2

stage

Pressing the soft key will also terminate the data entry and return the instrument to the

measurement screen.

Main Page

Table of Contents3
Safety9
General9
AC Power Supply10
Adjustment, Maintenance and Repair10
Static Electricity11
Introduction13
Figure 2-1 4300 LCR Meter13
Installation15
Schedule of Equipment15
AC Line Connections15
Location16
Measurement Connections16
Operation17
The Rear Panel17
AC Power Inlet17
Figure 4-1 the 4300 Rear Panel17
Fuse Holder18
Rear Panel Control Connections18
DC Bias Input18
Usb18
Lan18
Trigger in18
Gpib19
Bin Handler20
The Front Panel21
Figure 4-2 the 4300 Front Panel21
Switching the Instrument on22
Contrast Adjustment22
Switching the Instrument off22
The Soft Keys22
Figure 4-3 the Soft Keys22
The Navigation Keys23
The Control Keys23
Figure 4-4 the Navigation Keys23
The Data Entry Keypad24
Trimming24
Performing an Open Circuit Trim and Short Circuit Trim25
Figure 4-5 Connections for O/C Trimming of Kelvin Clips25
Figure 4-7 Calibrate Pull down Menu25
Figure 4-8 Open Circuit Trim Page26
Figure 4-9 Open Circuit Trim in Progress26
Measurement27
Figure 4-10 Short Circuit Trim Page27
Figure 4-11 Short Circuit Trim in Progress27
Main Menu28
Settings Page28
Status Page29
External Control Page29
Figure 4-14 Status Page Example29
Figure 4-15 External Control Page29
Measurement Screen30
Set Pull down Menu30
Figure 4-16 Typical Measurement Screen30
Figure 4-17 Set Pull down Menu and Soft Keys30
Function 131
Function 231
Figure 4-18 Function 1 Selection Page32
Equivalent Circuit33
Figure 4-19 Function 2 Selection Page33
Figure 4-20 Equivalent Circuit Selection Page33
Frequency34
Figure 4-21Frequency Setting34
Figure 4-22 Frequency Setting34
AC Drive Level35
Figure 4-23 AC Drive Level Setting35
Figure 4-24 AC Drive Level Setting35
Measurement Speed36
DC Bias Voltage36
Figure 4-25 Measurement Speed Selection Page36
Figure 4-26 DC Bias Voltage Selection Page36
Range37
DC Resistance37
Figure 4-27 Hardware Range Selection Page37
Figure 4-28 Rdc Measurement Screen37
Figure 4-29 DC Resistance Selection Page38
Option Pull down Menu39
Scale39
Figure 4-30 Option Pull down Menu39
Figure 4-31 Scale Initial Page39
Figure 4-32 Bar Graph Explanation40
External Control41
Buzzer41
Figure 4-33 External Control Selection Screen41
More Pull down Menu42
Recall42
Figure 4-34 more Pull down Menu42
Figure 4-35 Recall Screen42
Save43
Binning (Option)43
Figure 4-36 Save Screen43
Binning - Set44
Figure 4-37 Binning Mode Screen44
Figure 4-38 bin Types Screen44
Figure 4-39 One Term Selection Screen45
Figure 4-40 One Term Dual Limits Selection Screen45
Figure 4-41 Two Term Selection Screen45
Figure 4-42 One Term Absolute Limits Screen46
Figure 4-43 One Term Percentage Limits Screen46
Figure 4-44 One Term Save Result Screen47
Figure 4-45 One Term Dual Limits Absolute Limits Screen48
Figure 4-46 One Term Dual Limits Percentage Limits Screen48
Figure 4-47 One Term Dual Limits Save Result Screen49
Figure 4-48 Two Term Absolute Limits Screen49
Figure 4-49 Two Term Percentage Limits Screen50
Binning - Sort51
Figure 4-50 Two Term Save Result Screen51
Figure 4-51 Sort Screen Example51
Binning - Count52
Figure 4-52 Count Screen Example52
Remote Control (Gpib & Rs-232)53
RS-232 Control53
Introduction53
Protocol53
Commands53
GPIB Control54
Introduction54
Interface Specification54
GPIB Address54
Message Syntax54
Figure 5-1 GPIB Message Structure55
Figure 5-2 GPIB Command Structure55
Data Output58
Status Reporting58
Figure 5-3 GPIB Data Output58
Figure 5-4 GPIB RMU Structure58
Service Request Enable Register59
Figure 5-5 Status Byte Register59
Figure 5-6 Standard Event Status Register60
Figure 5-7 Event Status Byte Register61
Figure 5-8 Standard Operation Status Group62
Common Commands63
Standard Operation Status Commands64
4300 Device-Specific Commands65
Command Summary65
Measurement Mode66
Calibrate Mode72
Root Commands73
Binning75
Overview75
Bin Types75
One Term bin Type75
Figure 6-1 One Term bin Type Diagram75
Figure 6-2 One Term bin Type Two Axis Diagram76
Figure 6-3 One Term bin Type Flow Chart76
One Term Dual Limits bin Type77
Figure 6-4 One Term Dual Limits bin Type Diagram77
Figure 6-5 One Term Dual Limits bin Type Two Axis Diagram77
Figure 6-6 One Term Dual Limts bin Type Flow Chart78
Two Term bin Type79
Figure 6-7 One Term Dual Limits bin Type Diagram79
Figure 6-8 Two Term bin Type Two Axis Diagram79
Figure 6-9 Two Term bin Type Flow Chart80
Signals81
Control Input81
Test Result Output81
Control Output81
Electrical Ratings81
Timing Diagram82
Figure 6-10 Binning Timing Diagram82
Sort84
Count84
Figure 6-11 Sort Screen84
Figure 6-12 Count Screen84
Lcr Meter Specification85
Measurement Parameters85
AC Functions85
Series or Parallel Equivalent Circuit85
Polar Form85
DC Function85
AC Drive Signal85
Frequency Range and Points85
Frequency Accuracy86
Frequency Step Size86
AC Drive Level86
Source Impedance86
DC Drive Level (Rdc)86
DC Bias Voltage86
Measurement Speed87
Measurement Range87
Modes of Operation88
Measurement88
Binning (Option)88
Save and Recall89
Measurement Connections89
Measurement Accuracy89
R/ G / y / Z Accuracy Chart90
Rdc Accuracy91
General91
AC Input91
Display91
Remote Control91
Remote Trigger91
Mechanical91
Environmental Conditions92
Temperature Range92
Relative Humidity92
Altitude92
Installation Category92
Pollution Degree92
Safety92
Emc92
Theory Reference93
Abbreviations93
Formulae93
Series/Parallel Conversions94
Polar Derivations94
Maintenance95
Support and Service96

Wayne 4310 - AC Drive Level; Figure 4-23 AC Drive Level Setting; Figure 4-24 AC Drive Level Setting

Table of Contents