EasyManua.ls Logo

YASKAWA P7 - Index

YASKAWA P7
256 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
Index - 1
A
A. TUNE.................................................................. 3-6, 3-13
AC Reactor .......................................................................E-6
Accel/Decel
Parameters .................................................................A-7
Switch Frequency......................................................A-7
Time ........................................................................ 5-25
Acceleration
Stall Prevention Level during ..............5-40, 6-16, A-20
Time................................................................ 5-25, A-7
Troubleshooting.......................................6-7, 6-10, 6-16
Access Level ........................................................... 5-2, A-2
ADV ........................................................................3-6, 3-12
Alarm Displays & Processing........................................... 6-8
ALARM Indicator ............................................................ 3-4
Altitude.............................................................................C-4
Ambient Temperature....................................1-13, 6-17, C-4
Analog Inputs
Bias.......................................................5-33, 5-38, A-16
Connection Diagram................................................ 2-27
Control Circuit Terminals........................................ 2-23
Gain ......................................................5-33, 5-38, A-16
Parameters ...............................................................A-16
Troubleshooting....................................................... 6-14
Analog Outputs
Bias.............................................................. A-17, A-18
Connection Diagram................................................ 2-27
Control Circuit Terminals........................................ 2-23
Gain .........................................................................A-17
Parameters .................................................... A-17, A-18
ASIC Faults ...................................................................... 6-3
Auto Restart.................................................................... 5-44
Count Reset ............................................................. 5-44
Faults Covered......................................................... 5-44
Max. Restart Time After Fault ................................ 5-44
Number of Attempts................................................ 5-44
Auto-Tuning
Fault Displays and Processing................................. 6-12
How to..................................................................... 5-59
Line-to-Line Resistance ..........................................A-11
Menu.................................................................3-6, 3-13
Motor Rated Current ...............................4-6, A11, A-25
Motor Rated Power .................................................A-25
B
Base Block
After Fault .....................................................5-44, A-19
Circuit Fault............................................................... 6-2
Minimum Time ....................................... 5-7, A-19, B-4
Basic Programming...............................................5-1 to 5-60
Baud Rate .........................................................6-8, D-2, D-4
Bias Adjustments.............................. 5-33, 5-38, A-16, A-18
Braking
DC Injection...............................................................5-9
High-Slip.................................................................A-23
Dynamic...................................................................2-12
Branch Short Circuit Protection................................E-2, E-3
Broken Belt (Undertorque detection)..............................5-46
C
Cable Length................................................................... 2-11
Capacitors .........................................................................7-2
Capacity, Rated Output ........................................... C-2, C-3
Capacity Related Parameters .......................................... B-1
Carrier Frequency
Error......................................................................... 6-11
Lower Limit ............................................................. A-8
Parameters................................................................. A-8
Proportional Gain ..................................................... A-8
Selection ...................................................................A-8
Upper limit ............................................................... A-8
Vs. Cable Length ..................................................... 2-11
Characteristic Frequency ................................................ 6-18
Charge Indicator (LED) ............................. 1-6, 2-2, 4-5, C-4
Circuit Breakers .................................................2-9, E-2, E-3
Clearances.......................................................................1-14
Coast to Stop.................................................. 5-6, 5-32, 5-48
Coast w/Timer.................................................................5-32
Com OPT Setup Parameters........................................... A-11
Communications Modbus/Serial................ A-18, D1 to D14
Errors (CPF)............................................. 6-2 to 6-4, 6-8
Parameters............................................................... A-18
Component Names.....................................................1-5, 1-6
Connections
Preventive Maintenance.............................................7-3
Connectors
Inspection...................................................................7-2
Sizing...............................................................2-3 to 2-7
Contactors
Magnetic ...................................................................E-6
Soft Charge .............................................................6-21
Control Circuit
Characteristics......................................... 6-7, 6-10, 6-21
Control Circuit (Continued)
Connection Diagram.........................................2-27
Analog Input Terminal Configuration .............2-21
PCB
Inspecting ...........................................................7-2
Spare Parts.................................................. F-2, F-3

Table of Contents

Related product manuals