YASKAWA SGMSV User Manual

5 Adjustments
5.6.2 Anti-Resonance Control Adjustment Function Operating Procedure
5-48
6
Press the Key. The cursor will move to "damp,"
and the flashing of "freq" will stop.
7
Select the digit with the or Key, and press
the or Key to set the damping gain.
Example of measured waveform
Note: Increase the damping gain from about 0 to
200% in 10% increments while checking the
effect of vibration reduction. If vibration reduc-
tion is still insufficient at a gain of 200%, can-
cel the setting, and lower the control gain by
using a different method, such as one-parame-
ter tuning.
8
If fine tuning of the frequency is necessary, press the
Key. The cursor will move from "damp" to
"freq." If fine-tuning is not necessary, skip step 9 and
go to step 10.
9
Select the digit with the or Key, and press
the or Key to fine-tune the frequency.
10
Press the Key to save the settings. "DONE" will
flash for approximately two seconds and "RUN" will
be displayed.
11
Press the Key to complete the anti-resonance
control adjustment function. The screen in step 1 will
appear again.
(cont’d)
Step Display after Operation Keys Operation
㧾㨁㧺㨂㨕㨎㧿㨡㨜  
㨒㨞㨑㨝㧩㧜㧠㧜㧜㧴㨦
㨐㨍㨙㨜㧩㧜㧜㧜㧜
㧾㨁㧺㨂㨕㨎㧿㨡㨜  
㨒㨞㨑㨝㧩㧜㧠㧜㧜㧴㨦
㨐㨍㨙㨜㧩㧜㧝㧞㧜
Error
Error
Torque reference
Torque reference
Positioning completed
Positioning completed
signal
signal
Error
Torque reference
Positioning completed
signal
㧾㨁㧺㨂㨕㨎㧿㨡㨜  
㨒㨞㨑㨝㧩㧜㧠㧜㧜㧴㨦
㨐㨍㨙㨜㧩㧜㧝㧞㧜
㧾㨁㧺㨂㨕㨎㧿㨡㨜  
㨒㨞㨑㨝㧩㧜㧠㧞㧜㧴㨦
㨐㨍㨙㨜㧩㧜㧝㧞㧜
㧾㨁㧺    㨂㨕㨎㧿㨡㨜  
㨒㨞㨑㨝㧩㧜㧠㧞㧜㧴㨦
㨐㨍㨙㨜㧩㧜㧝㧞㧜
㧾㨁㧺㧲㨁㧺㧯㨀㧵㧻㧺  
㧲㨚㧞㧜㧟㧦㧻㨚㨑㧼㨞㨙㨀㨡㨚
㧲㨚㧞㧜㧠㧦㧭㨂㨕㨎ޓ㧿㨡㨜
㧲㨚㧞㧜㧡㧦㨂㨕㨎ޓ㧿㨡㨜
㧲㨚㧞㧜㧢㧦㧱㨍㨟㨥ޓ㧲㧲㨀

YASKAWA SGMSV Specifications

General

Brand	YASKAWA
Model	SGMSV
Category	Servo Drives
Language	English