Yealink VC110 - User Manual

Other manuals for Yealink VC110

Administrator's Guide321 pages

Admin Guide233 pages

Quick Start Guide20 pages

Quick Guide8 pages

Deployment Guide5 pages

Questions and Answers:

J
Justin KirkAug 31, 2025
Why does my Yealink Conference System endpoint fail to upgrade?
- P
  Phillip PhillipsAug 31, 2025
  If your Yealink Conference System endpoint fails to upgrade, ensure that the firmware version is different from the one currently in use. Verify that the downloaded firmware is specifically designed for your endpoint model. Make sure the endpoint remains powered on and connected to a stable network throughout the upgrade. If upgrading via the web user interface, avoid refreshing or closing the page during the process.
A
arodriguezAug 25, 2025
What to do if I can’t hear audio during a call on my Yealink VC110 Conference System?
- R
  Reginald DixonAug 25, 2025
  If you can't hear audio during a call, ensure the local audio output device is correctly connected. Use audio diagnostics to check if the audio device is working normally. Make sure the ringer volume isn't set to the minimum. Also, check if the far site is muted.
A
Amanda BarajasAug 25, 2025
Why does my Yealink Conference System network keep losing packets?
- C
  copelandshannonAug 26, 2025
  If the network keeps losing packets, check the network availability and ensure the LED indicator on the Internet port illuminates green. Try using a low-speed connection to check for packet loss. Also, check the configuration of the network speed and duplex mode on the endpoint, switch, and router.
B
Brittany LeeAug 26, 2025
Why Yealink Conference System endpoint fails to call the far site via IP address?
- D
  Diane GreenAug 26, 2025
  If the endpoint fails to call the far site via IP address, ensure that at least one call protocol is enabled on both sites. Verify that the network is connected and configured correctly. If issues persist, ping the IP address of the far site.
V
Victoria McdonaldAug 26, 2025
How to check network availability on Yealink Conference System?
- J
  johnsoncoreyAug 27, 2025
  If the network is unavailable for your Yealink Conference System, check if the network is available and if the LED indicator on the left of the Internet port is green.
S
Stephanie EvansAug 27, 2025
What to do if my Yealink VC110 endpoint fails to call the far site?
- J
  joycesusanAug 27, 2025
  If your Yealink Conference System endpoint can't call the far site, verify that the near and far site networks are available. Check if the far site has enabled the DND (Do Not Disturb) feature, and confirm that the accounts are correctly registered, with the appropriate account used for the call. Ensure the number you're calling is correct and that the far site isn't rejecting your call. Also, check if a firewall is blocking inbound traffic or if the far site has reached its maximum call-in limit. If encryption is required, make sure both sites have it enabled and support the same call protocol.
J
John LewisAug 27, 2025
Why is my Yealink Conference System remote control not working?
- S
  stevensmithAug 27, 2025
  If the remote control for your Yealink Conference System isn't working, check if the endpoint is powered on. Ensure the battery's positive and negative charges are correctly connected, and verify the battery has sufficient power. Also, make sure there are no special fluorescent or neon signs nearby that could interfere with the remote control's signal.
A
Andrew CruzAug 27, 2025
How to improve bad video quality on Yealink VC110?
- E
  erinbrownAug 27, 2025
  If the video quality on your Yealink Conference System is poor, ensure the display device has a suitable resolution. Check for packet loss and verify that the camera settings, such as brightness and white balance, are correctly configured. Avoid high-intensity indoor light or direct sunlight on the camera.
S
shepherddavidAug 28, 2025
How to troubleshoot poor audio quality on Yealink VC110 Conference System?
- T
  tara84Aug 28, 2025
  If you're experiencing poor audio quality with your Yealink Conference System, ensure the local audio output device is correctly connected. Use the audio diagnose feature to check if the audio device is working normally. Make sure the ringer volume isn't set to the minimum and check if the far site is muted. Verify the local audio input device is correctly connected, and that the near site isn't muted. Also, check if the endpoint has enabled the auto-answer mute feature.
R
Robert DavisAug 28, 2025
Why doesn't the Yealink VC110 Conference System display IP address?
- L
  Laura NolanAug 28, 2025
  If the status bar of your Yealink Conference System's display device isn't showing the IP address, check if the network is available. Ensure the LAN property is configured correctly and verify if the endpoint has enabled the hide IP address feature. Also, check if the endpoint has configured the firewall and NAT correctly.

Yealink VC110 Specifications

General

Digital zoom	4 x
Focus adjustment	Auto
Video codecs	H.264, H.263
Maximum frame rate	30 fps
Supported video modes	720p, 1080p
Video formats supported	H.263, H.264
Supported graphics resolutions	352 x 288, 704 x 576, 1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecs	G.711a, G.722, G.722.1, G.722.1C
Line-in	Yes
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Pan range	-100 - 100 °
Tilt angle range	-30 - 30 °
Security algorithms	128-bit AES, HTTPS, SRTP, SSL/TLS
Ethernet LAN data rates	10, 100 Mbit/s
Supported network protocols	TCP/IP (IPv4), DHCP/ stastic IP, HTTP/ HTTPS, SRTP/TLS, IEEE802.1X, LLDP-MED, VLAN
Current	2 A
Power consumption (max)	30 W
Power consumption (typical)	24 W
Storage temperature (T-T)	-20 - 50 °C
Operating temperature (T-T)	10 - 40 °C
Operating relative humidity (H-H)	10 - 95 %