Index-2
Index
changing the ripple limits color, 1-92
channel coupling, 7-11
channel position softkey, 1-17
channel stimulus coupling, 7-15
channels 1 and 2, coupling power, 1-59
characteristics of the filter, 1-72
characterizing a duplexer, 1-50
definitions, 1-50
procedure, 1-50
characterizing microwave systematic
errors
, 7-43
device measurement, 7-48
one-port error model, 7-43
two-port error model, 7-48
choosing
display elements, 4-13
measurement parameters, 1-4
plot speed, 4-16
scale, 4-15
chop sweep mode, activating, 5-12
CITIfile, 4-39
clarifying type-N connector sex, 6-4
clearing a sequence from memory, 1-105
color
changing the ripple limits, 1-92
ripple test message, 1-91
color printer, using, 4-6
colors of the display, adjusting, 1-22
default, 1-22
intensity, 1-22
modified, 1-23
modify colors menu, 1-22
command
deleting, 1-103
inserting, 1-104
modifying, 1-104
commands
GPIB, 1-124
commands that require clean sweep,
1-108
commands that sequencing completes
before next command, 1-108
comma-separated values. See CSV
format
compensating for directional coupler
response
, 6-35
compliance with German noise
requirements, 8-8
computer, what you can save, 4-35
confidence check, 6-65
configuration
high power one, 1-67
high power three, 1-70
high power two, 1-69
configuring
plot function, 4-9
configuring two sources, 2-29
connecting
device under test, 1-4
required test equipment, 1-4
connector
care, 5-3
repeatability, 5-4
continuous correction mode, using, 6-38
continuous markers, 1-24
controlling external switches, 1-122
GPIB commands, 1-124
manual, 1-122
sequencing programs, 1-123
conversion, 7-8
conversion compression using
frequency offset mode
, 2-39
conversion loss, 2-20
conversion loss using frequency offset
mode
, 2-13
conversion menu, 7-23
copy mode, 7-81
correction, sampler/IF, 7-7
coupling display markers, 1-31
coupling power between channels 1 and
2, 1-59, 7-89
coupling, channel stimulus, 7-15
creating
flat limit lines, 1-77
sequence, 1-101
sloping limit line, 1-79
user-defined TRL calibration kit, 6-50
user-defined TRM calibration kit, 6-54
creating single point limits, 1-81
crosstalk, 7-42
CSV format, saving measurement results
in
, 4-42
CW frequency range in external source
mode
, 7-86
CW frequency, setting, 1-39
CW time measurements, 3-22
CW time sweep, 7-20
D
data formats, ASCII, 4-39
data processing, 7-6
processing details, 7-7
data trace, 1-19
saving to display memory, 1-19
decision making functions, 1-114
decoupled
channel power, 1-14
stimulus, 1-13
decreasing
frequency span, 5-10
sweep rate, 5-8
time delay, 5-8
decrementing the loop counter, 2-31
default colors, 1-22
defining
plot function, 4-13
print function, 4-6
defining a print function
color printer, using, 4-6
resetting print parameters to default
value
, 4-7
delay block, electrical, 7-8
delay, determining electrical, 6-73
delay, electrical, 7-35
delay, group, 1-47, 2-34
deleting
commands, 1-103
frequency signals, 6-35
line segments, 1-82
deleting a file, 4-49
all files, 4-49
instrument state file, 4-49
delta markers, 1-28
demodulating the results of the forward
transform
, 3-23
designing your own fixture, 6-49
detecting IF delay, 5-10
detection, IF, 7-7
deviation from linear phase, 1-47
device measurement, 7-48
device measurements, 6-4
device under test
measuring, 1-5
device under test, connecting, 1-4
device, bilateral, 6-22, 6-25
device, noninsertable, 6-69
direct sampler access configurations,
using
, 5-16
directional coupler response,
compensating for, 6-35
discrete markers, 1-24
disk
formatting, 4-51
disk, plotting a measurement to, 4-11
display elements, choosing, 4-13
display functions, 1-10
active channel display, 1-11
titling, 1-11
adjusting colors of the display, 1-22
blanking the display, 1-21
data trace
saving to display memory, 1-19
four-channel display
4 Param Displays softkey, 1-18
Channel Position softkey, 1-17
customizing, 1-17
viewing, 1-14
measurement data
dividing by the memory trace, 1-20
subtracting memory trace, 1-20
viewing, 1-20
To Next Page
Loading...
Need help?
General
