Analog Devices AD9361 User Manual

AD9361 Reference Manual UG-570
| Page 3 of 128
Slow Attack AGC Gain Update Time ....................................... 40
Overloads in Slow Attack AGC Mode ...................................... 41
Slow Attack AGC and Gain Tables ........................................... 41
Hybrid AGC Mode ..................................................................... 42
Fast Attack AGC Mode ............................................................... 42
State 0: RESET ............................................................................. 43
State 1: Peak Overload Detect ................................................... 43
State 2: Measure Power and Lock Level Gain Change ........... 44
State 3: Measure Power and Peak Overload Detect ................ 44
State 4: Unlock Gain ................................................................... 44
State 5: Gain Lock and Measure Power .................................... 45
Custom Gain Tables ........................................................................ 47
Overview ...................................................................................... 47
RF DC Cal Bit .............................................................................. 49
Maximum Full Table/LMT Table Index ................................... 49
External LNA ............................................................................... 49
Received Signal Strength Indicator (RSSI) .................................. 50
Overview ...................................................................................... 50
Mode Select and Measurement Duration ................................ 50
RSSI Weighting ............................................................................ 50
RSSI Delay and RSSI Wait .......................................................... 50
RSSI Preamble and RSSI Symbol .............................................. 51
RSSI RFIR ..................................................................................... 51
RSSI Gain Step Calibration ........................................................ 51
Transmit Power Control ................................................................. 55
Overview ...................................................................................... 55
Tx Attenuation Words ................................................................ 55
Attenuation Word Update Options .......................................... 55
Tx Power Monitor ........................................................................... 56
Overview ...................................................................................... 56
Tx Power Monitor Description ................................................. 56
Input Matching/Attenuation Network ..................................... 57
Tx Power Monitor Gain Control ............................................... 58
TPM Dynamic Range ................................................................. 59
Example of Tx Mon Configuration and Measurement of TPM
Transfer Function ........................................................................ 59
TPM Test Mode ........................................................................... 60
RF Port Interface ............................................................................. 61
Overview ...................................................................................... 61
Rx Signal Path Interface ............................................................. 62
Tx Signal Path Interface ............................................................. 69
Factory Calibrations ....................................................................... 71
Overview ...................................................................................... 71
Internal DCXO ............................................................................ 71
Tx RSSI (Tx Monitor) ................................................................. 71
Rx RSSI ......................................................................................... 71
Rx GM/LNA Gain Step Calibration ......................................... 72
Tx Power Out vs. Tx Attenuation and Tx Power Out vs.
Carrier Frequency ....................................................................... 72
Control Output ................................................................................ 73
Overview ...................................................................................... 73
Description of Control Output Signals .................................... 74
0x035 = 0x00 (Calibration Busy and Done) ............................ 74
0x035 = 0x01 (PLL Lock) ........................................................... 75
0x035 = 0x02 (Calibration Busy) .............................................. 75
0x035 = 0x03 (Rx Gain Control) .............................................. 75
0x035 = 0x04 (Rx Gain Control) .............................................. 76
0x035 = 0x05 (Rx Gain Control) .............................................. 76
0x035 = 0x06 (Rx Gain Control) .............................................. 76
0x035 = 0x07 (Rx Gain Control) .............................................. 76
0x035 = 0x08 (Rx Gain Control) .............................................. 76
0x035 = 0x09 (RxOn, TxOn, RSSI) .......................................... 77
0x035 = 0x0A (Digital Overflow) ............................................. 77
0x035 = 0x0B (Calibration and ENSM States) ........................ 77
0x035 = 0x0C (Gain Control) ................................................... 77
0x035 = 0x0D (Tx Quadrature and RF DC Calibration
Status) ........................................................................................... 78
0x035 = 0x0E (Rx Quadrature and BB DC Calibration
Status) ........................................................................................... 78
0x035 = 0x0F (Gain Control) .................................................... 78
0x035 = 0x10 (Gain Control and RSSI) ................................... 78
0x035 = 0x11 (AuxADC Digital Output) ................................ 78
0x035 = 0x12 (Gain Control, Power Word Ready)................. 78
0x035 = 0x13 (Gain Control, Power Word Ready)................. 79
0x035 = 0x14 (Digital Overflow) .............................................. 79
0x035 = 0x15 (DC Offset Tracking) ......................................... 79
0x035 = 0x16 (Gain Control) .................................................... 79
0x035 = 0x17 (Gain Control) .................................................... 80
0x035 = 0x18 (DC Offset Tracking, Power Word Ready) ..... 80
0x035 = 0x19 (Charge Pump Calibration States) ................... 80
0x035 = 0x1A (Rx VCO and ALC Calibration States) ........... 80
0x035 = 0x1B (Tx VCO and ALC Calibration States) ........... 80
0x035 = 0x1C (Rx VCO Calibration States) ............................ 80
Rev. A

Analog Devices AD9361 Specifications

General

Brand	Analog Devices
Model	AD9361
Category	Motherboard
Language	English