Anthos A3 Plus - Page 104

A3 PLUS - A5 - A6 PLUS - L6
SURGICAL SINGLE CART
104
EN
IEC 61000-4-2
relevant humidity should be at least 30%.
Proximity fields from RF
wireless
communications
IEC 61000-4-3
27 V/m at 385 MHz
28 V/m at 450, 810, 870, 930,
1720, 1845, 1970, 2450 MHz
9 V/m at 710, 745, 780, 5240,
5500, 5785 MHz
IEC 60601-1-2
Test level
Portable and mobile RF communications equipment
should be used no closer to any part of the dental unit,
including cables, than the minimum distance
recommended in this section.
IEC 61000-4-4
fast/burst electric
transients
±2 kV for power supply lines
±1 kV for input/output lines >
3 m
IEC 60601-1-2
Test level
The power supply line quality should be that of a typical
commercial or hospital environment.
Over-voltage
IEC 61000-4-5
±1 kV differential
mode
±2 kV common mode
IEC 60601-1-2
Test level
The power supply line quality should be that of a typical
commercial or hospital environment.
Voltage drops, short
interruptions and
voltage change on the
IEC 61000-4-11 input
electric line
Ut = 0% (at 0°, 45°,
90°, 135°, 180°, 225°,
270°, 315°) for 0.5 cycles
Ut = 0% for 1 cycle
Ut = 70% (at 0°) for 25/30
cycles
Ut = 0% for 250/300 cycles
IEC 60601-1-2
Test level
The power supply line quality should be that of a typical
commercial or hospital environment. If the dental unit
user requires a continuous operation also in case of
blackout, it is recommended to power the dental unit
with uninterruptible power supply or batteries.
Magnetic field at
network frequency
(50/60 Hz)
IEC 61000-4-8
30 A/m
IEC 60601-1-2
Test level
The magnetic fields at network frequency should
feature levels typical of a standard commercial or
hospital environment.
Guidance and Manufacturer's declaration - Electromagnetic immunity
The dental unit is designed to operate in the specified electromagnetic environment. The customer or user of the dental unit must
ensure that it is used in such environment.
Immunity test
IEC 60601-1-2
Test level
Level of
conformity
Electromagnetic Environment
The RF communication devices (portable and mobile)
must not be used at a distance from the dental unit and
its components, including cables, lower than the
recommended distance calculated using the
corresponding equation applicable to the transmitter
frequency.
Recommended distance.
Radiated RF
EN 61000-4-3
3 V/m
from 80 MHz to 2.7 GHz
IEC 60601-1-2
Test level
d = 1.2 x √P 80 MHz to 800MHz
d = 2.3 x √P 800 MHz at 2.7GHz
Conducted RF
EN 61000-4-6
3 V
from 150 kHz to 80 MHz
6 V
ISM frequencies
IEC 60601-1-2
Test level
d = 1.2 x √P
Where P is the maximum output power of the
transmitter in Watt (W) according to the transmitter
Manufacturer, and d is the recommended distance in
metres (m).
The field intensity of the fixed RF transmitters,
determined based on an electromagnetic site, could be
lower than the conformity level in each frequency
interval.
Near the equipment with the following symbol
interferences can be caused:
Recommended distance between the RF portable and mobile communication devices and the dental unit.
The dental unit is intended for use in electromagnetic environment where RF irradiated disturbances are controlled. The customer or
the user of the dental unit can prevent electromagnetic interferences by ensuring a minimum distance between RF mobile and
portable (transmitter) communication devices and the dental unit as shown below, according to maximum power output of the
communication devices.
Transmitter maximum nominal output
(W)
Distance according the transmitter frequency
(m)
from 150 KHz to 80 MHz
d = 1.2 x √P
from 80 KHz to 800 MHz
d = 1.2 x √P
from 800 KHz to 2.7
MHz
d = 2.3 x √P
0.01
0.12
0.12
0.23
0.1
0.38
0.38
0.73
1
1.2
1.2
2.3