Baumuller BM4400 - Effects of the Different Charging Circuits; Table of Charging Times

Power on switching frequency / DC link charging
Instruction handbook b maXX BM4400, BM4600, BM4700
Document No.: 5.12008.07 Baumüller Nürnberg GmbH
228
of 358
8.3
8.3.5 Effects of the different charging circuits
Following incompatibilities result because of charging and must be checked by the user
operating devices with the new current-controlled charging-method.
m Ch
arging time: Adapt timeout values in master-control to avoid possible error messag-
es because of not in time ready-to-operate signal.
m En
sure clockwise-rotating-field. The device does not identify the direction of the rotat-
ing field. 
In case of a counter-clockwise-rotating-field no charging is done, after 20 s the attempt
o
f charging is stopped and error 089 (power unit not ready-to-operate) is generated. 
In rare cases a counterclockwise rotating field
can cause an abrupt charging and a
tripped fuse.
For error correction two power supply ph
ases must be exchanged, e. g. the cables
connected to 1U1 and 1V1. The error is corrected, assumed there is no other error.
The advantages of the current-controlled charging are (in short):
m The maximum chargeable DC link cap
acity is higher than without the current-controlled
charging.
m The dependency of the DC link capacity on the charging current is reduced. The self-
p
rotection level of the device against incorrect dimensioning is improved.
8.3.6 Table of charging times
Device Inductance
power choke
Internal
capacity
Typical
charging
time
at 300 V
Typical
cha
rging
time
at 400 V
Typical
ch
arging
time
at 480 V
Typical
ch
arging time
at 530 V
BM4632 0.19 mH 3000 µF 0.08 s 0.18 s 0.34 s 0.48 s
BM4443 0.36 mH 1880 µF 0.1 s 0.22 s 0.4 s 0.56 s
BM4444 0.26 mH 2350 µF 0.1 s 0.22 s 0.42 s 0.5 s
BM4445
BM4642
0.26 mH 3055 µF 0.11 s 0.26 s 0.47 s 0.65 s
BM4446 0.18 mH 3760 µF 0.09 s 0.22 s 0.4 s 0.57 s
BM4452 0.26 mH 3000 µF 0.11 s 0.25 s 0.47 s 0.66 s
BM4453 0.18 mH 3000 µF 0.08 s 0.18 s 0.32 s 0.45 s
BM4454
BM4652
BM4755
105 µH 6600 µF 0.1 s 0.24 s 0.4 s 0.58 s
BM4462 105 µH 6000 µF 0.09 s 0.22 s 0.38 s 0.52 s
BM4463 80 µH 6000 µF 0.07 s 0.16 s 0.29 s 0.4 s
BM4466
BM4766
80 µH 13.2 mF 0.14 s 0.33 s 0.61 s 0.86 s
BM447X 39 µH 19.8 mF 0.12 s 0.29 s 0.51 s 0.7 s
BM477X 32.6 µH 19.8 mF 0.1 s 0.24 s 0.4 s 0.58
s