BeaconMedaes TotalAlert 2 - Monitoring Mode (Cont.); Multiplexer; LED Module; Digital Display Module

144 pages

Save Page as PDF

To Next Page

To Previous Page

6-847718-00 Rev. B00

Operation

Figure 91: Transfer Setup

Figure 92: Transfer Setup Complete

Main Page

Table of Contents3
Product Identification6
Alarm Modular Components7
- Annunciator Module7
- Multiplexer Module7
- LED Module7
- Breakout Board7
- Relay Board8
- Digital Display Module8
- Multi-Signal Module8
- Blank Module8
Definition of Statements9
Definitions9
Alarm Configurations12
- Master Alarms13
- Area Alarms14
- Combo Alarms16
Electromagnetic Compatibility18
- Fcc18
- Ices-00318
- Master Alarms23
- Area Alarms23
- Combo Alarms24
Rough-In25
- Alarm Panel Back Box25
- Remote Sensor Back Box26
- Pipeline Connection27
Pull Wire29
- General Requirements29
- Wire Type and Size29
- Wire Routing30
- Determining Number of Conductors31
Wiring32
- Power Supply32
- Remote Sensor33
- Breakout Board Inputs34
- Relay Board Outputs35
- Multi-Signal Module Inputs36
- Digital Display Module Master/Slave37
- Multi-Signal Module Relays37
- General Fault / Aux Relays38
- Digital Display Module High / Lowrelays38
- Ethernet39
- Building Automation System39
- Field Wiring Cable Shield Grounding41
Finish42
- Front Panel Mounting42
- Local Sensor43
- Remote Sensor44
- Labeling45
Wiring Schematic 1: Power Supply48
Wiring Schematic 2: Sensor Module to Digital Display Module49
Wiring Schematic 3: Multiplexer / Breakout Boards50
Wiring Schematic 4: Relay Board51
Wiring Schematic 5: Multi-Signal Module Inputs52
Wiring Schematic 6: Digital Display Module Master/Slave53
Wiring Schematic 7: Multi-Signal Module Relay Outputs54
Wiring Schematic 9: Digital Display Module High / Low Relays55
Wiring Schematic 8: General Fault / Auxiliary Relays55
Wiring Schematic 10: Remote Pressure / Vacuum Switches56
Wiring Schematic 11: Johnson Controls Metasys® N2 Connection57
Start-Up and Checking58
- Master Alarm Panel58
- Area Alarm Panel59
- Combo Alarm Panel60
Set-Up Procedures61
- Annunciator Module61
- Multiplexer Module64
- Digital Display Module66
- Digital Display Module-Advanced68
- Multi-Signal Module71
- Multi-Signal Module-Advanced72
Set-Up Network Interface74
Set-Up Using Web Pages78
- Accessing the Web Page78
- Login in to Setup Pages79
- Enroll Devices80
- Setup Alarm Messages82
- Setup Area Alarms86
- Setup Device88
- Electronic Notification90
- Electronic Notification - Server Setup91
- Set Clock92
- Administer Users93
- Setup Network94
- Clear Network96
- Clear Event Log98
- Transfer Setup100
Monitoring Mode102
- Annunciator Module102
- Multiplexer / LED Module103
- Digital Display Module103
- Multi-Signal Module104
- Browsing Alarm Web Pages105
  - Accessing the Web Page105
  - Current Alarms106
  - Signals107
  - Network Devices108
  - View Device109
  - Device Information110
  - Event Log111
  - Diagnostics112
  - Download Configuration113
  - Network Statistics114
- Alarm System116
- Annunciator Module116
- Multiplexer Module118
- Digital Display Module119
- Multi-Signal Module120
- Power Supply121
- Troubleshooting Guide122
- Front Panel Components - Area Alarm131
- Front Panel Components - Master Alarm132
- Front Panel Components - Combo Alarm133
- Back Box Components - Area Alarm134
- Back Box Components - Master / Combo Alarm135
- Breakout and Relay Board Components - Master / Combo Alarm136
- Sensor Components137
- Labeling138
- Field Installation Kits138
Notes139
Master Alarm Signal Input Data140
Warranty142

BeaconMedaes TotalAlert 2 - Monitoring Mode (Cont.); Multiplexer; LED Module; Digital Display Module

Table of Contents

Related product manuals