Need help?Do you have a question about the BeaconMedaes TotalAlert 2 and is the answer not in the manual?
General| Brand | BeaconMedaes |
|---|---|
| Model | TotalAlert 2 |
| Category | Security System |
| Language | English |
Describes the annunciator module features and indicators.
Details monitoring capabilities and gas service indicators.
Explains adding extra gas service indicators to a multiplexer.
Covers screw terminals for dry-contact switch signals.
Describes screw terminals for 32 dry-contact relay outputs.
Explains digital LED readout of system pressure and alarm indications.
Details monitoring of up to five dry contact switch signals.
Reserves space in the alarm panel for future expansion.
Protocol for learning MAC addresses for Ethernet packet transmission.
Alarm panel monitoring medical gas and vacuum systems in a specific area.
Relay output on annunciator module for remote alarms or BMS.
Combines master alarm panel and area alarm panel features.
Verification of product standards for electromagnetic energy.
Standard high-speed network medium specified by IEEE 802.3.
Device connecting multiple Ethernet devices, broadcasting all messages.
Device connecting multiple Ethernet devices, optimizing message delivery.
Protocol for reliable data stream transmission between devices.
Protocol for fast, efficient short message transmission.
Abbreviation for Vacuum Fluorescent Display.
Describes the features and series designation for master alarm panels.
Describes the features and series designation for area alarm panels.
Describes the features and series designation for combo alarm panels.
Details conditions for device operation under FCC rules.
States compliance of digital apparatus with Canadian ICES-003 standards.
Provides EMC precautions for medical electrical equipment.
Details RF, harmonic, and voltage/flicker emissions compliance.
Outlines immunity tests and environmental guidance for ESD, transients, and fields.
Lists sequential installation steps for master alarm panels.
Lists sequential installation steps for area alarm panels.
Lists sequential installation steps for combo alarm panels.
Instructions for preparing and mounting the alarm panel back box.
Details braze connections for sensor rough-in to piping system drops.
Describes recommended DISS connection kits for pressure switches.
Outlines standards for powering, protecting, and wiring alarms.
Specifies criteria for low voltage wiring, including copper wire size and cable type.
Details conduit knockouts and hole usage for AC mains and low voltage wiring.
Clarifies wiring requirements for digital display modules, switched inputs, and relays.
Details power requirements and connection procedures for alarm panels.
Guides routing and connecting sensor wires to digital display modules.
Explains connecting source equipment signal wires to breakout board terminals.
Describes connecting field installed relay output signal wires to relay board terminals.
Guides connecting source equipment signal wires to multi-signal module terminals.
Explains wiring digital display modules to duplicate pressure readings.
Details the function of optional output relays on multi-signal modules.
Describes the general fault and auxiliary relays on the annunciator module.
Details the high and low pressure alarm relays on digital display modules.
Explains connecting alarms in a TotalAlert network via Ethernet.
Details compatibility with Johnson Controls Metasys® N2 system.
Provides mapping details for building automation system integration.
Instructions for grounding field wiring cable shields inside the alarm panel back box.
Step-by-step guide for mounting the front panel assembly.
Instructions for inserting and securing local sensor modules.
Procedures for wiring and installing remote sensor modules.
Instructions for labeling LEDs on multiplexer and LED modules with gas identification.
How to label the annunciator module using panel location labels.
Guides labeling digital display modules using provided location labels.
Instructions for labeling multi-signal modules with system status labels.
Details labeling the sensor module with monitored location information.
Shows wiring for local sensors to digital display modules.
Illustrates wiring for remote sensors to digital display modules.
Procedures for turning on and verifying alarm panel functionality.
Specific start-up and checking observations for master alarm panels.
Specific start-up and checking observations for area alarm panels.
Specific start-up and checking observations for combo alarm panels.
Guides setting up parameters using front panel controls and web pages.
Procedure to reset user credentials and network IP settings to factory defaults.
Steps to revert all annunciator module settings to factory defaults.
Details setting audible alarm repeat time and display intensity.
Explains changing units and alarm set points for digital display modules.
Adjusts communication parameters like network address and baud rate.
Guides changing signal options, enabling/disabling locations.
Lists necessary hardware for connecting to the network.
Details connecting devices to switches, hubs, or PCs.
Describes how the device obtains IP configuration via DHCP.
Explains using a pre-assigned fixed IP configuration.
Guides users on how to open the alarm's home page in a web browser.
Explains the login process and default credentials for accessing setup pages.
Instructions for adding other devices to the medical gas network.
Configures switched alarm signals, including gas type, message, and LED assignment.
Guides through selecting gas type, message, and LED for alarm inputs.
Details custom gas type entry and signal setup summary.
Explains assigning LED numbers and locations for alarm inputs.
Shows the signal setup summary and return options.
Configures alarm panel name, location, N2 address, and contact information.
Configures email, pager, or phone text message notifications.
Manages user accounts, including setting usernames and passwords.
Configures network settings, including IP addressing mode and discovery.
Clears and refreshes the device list memory for network devices.
Clears the event log entries from the alarm panel.
Transfers configuration settings from one compatible master alarm to another.
Explains how the VFD displays local and remote alarm signals and errors.
Describes how LEDs indicate signal status and alarm conditions.
Explains how digital displays show pipeline pressure/vacuum and alarm states.
Details how indicators on multi-signal modules show signal status.
Guides on how to access the alarm panel's web interface using browser.
Displays a snapshot of current alarms, including source, digital, and remote area alarms.
Shows all local signals monitored by the alarm panel.
Displays a snapshot of devices on the alarm network.
Shows the status of a remote device from the network devices list.
Displays detailed information about a specific device.
Shows a log of events that have occurred on the alarm panel.
Accesses diagnostic tools like configuration download and network statistics.
Allows saving the alarm configuration to a file.
Displays network statistics, including IP, MAC, packet counts, and errors.
Recommends periodic testing of the alarm system using self-test modes.
Details the self-test sequence for the annunciator module.
Lists and illustrates components of the area alarm front panel.
To Next Page
