Bosch radlonlcs D6412 - Page 4

Page 445349D © 2002 Radionics
D6412/D4412 Installation Guide
D6412/D4412
Contents
10.0 Off-Board Outputs ............................................................................................................................................................ 42
10.1 Overview ............................................................................................................................................................................. 42
10.2 DX3010 Octo-Output Module ............................................................................................................................................. 42
10.2.1 Overview ............................................................................................................................................................................. 42
10.2.2 Configuring the DX3010 Octo-Output Module .................................................................................................................. 42
10.2.3 Relay Outputs ..................................................................................................................................................................... 42
10.2.4 Installation ........................................................................................................................................................................... 43
10.2.5 DX3010 to D6412/D4412 SDI Bus Wiring Connections .................................................................................................. 44
10.2.6 Address Programming ....................................................................................................................................................... 45
11.0 Arming Devices ................................................................................................................................................................. 46
11.1 Description .......................................................................................................................................................................... 46
11.2 Command Centers ............................................................................................................................................................. 46
11.2.1 Assigning the Command Center an Address ................................................................................................................... 46
11.2.2 Command Center Installation ............................................................................................................................................ 47
11.3 D268/D269, D279 Independent Zone Control .................................................................................................................. 48
11.4 Keyswitch ............................................................................................................................................................................ 49
11.4.1 Keyswitch Description ........................................................................................................................................................ 49
11.4.2 Keyswitch Programming .................................................................................................................................................... 49
11.4.3 Keyswitch Installation ......................................................................................................................................................... 49
11.4.4 Keyswitch Operation........................................................................................................................................................... 49
12.0 SDI Devices........................................................................................................................................................................ 50
12.1 Description .......................................................................................................................................................................... 50
12.2 Installation ........................................................................................................................................................................... 50
12.3 DX4010 RS-232 Serial Interface Module .......................................................................................................................... 51
12.3.1 DX4010 Installation ............................................................................................................................................................ 52
12.3.2 DX4010 to D6412/D4412 SDI Bus Wiring Connections .................................................................................................. 52
12.3.3 RAM IV Direct Connection ................................................................................................................................................. 52
12.3.4 Configuration Jumpers ....................................................................................................................................................... 53
12.3.5 Supervision ......................................................................................................................................................................... 54
12.3.6 DX4010 Module’s DB9 Connector..................................................................................................................................... 54
13.0 Installer’s Keypad and Installer Mode ........................................................................................................................... 55
13.1 Installer’s Keypad Connector............................................................................................................................................. 55
13.2 Entering the Installer Mode ................................................................................................................................................ 55
13.2.1 Installer’s Passcode ........................................................................................................................................................... 55
13.2.2 Service Start/Service End Reports .................................................................................................................................... 56
13.3 Installer’s Menu................................................................................................................................................................... 56
13.3.1 Press [1] for Bell Test ......................................................................................................................................................... 56
13.3.2 Press [2] for Strobe Test ..................................................................................................................................................... 56
13.3.3 Press [3] for Battery Test .................................................................................................................................................... 56
13.3.4 Press [4] for Test Report .................................................................................................................................................... 56
13.3.5 Press [5] for Point Status ................................................................................................................................................... 56
13.3.6 Press [6] for Output Test .................................................................................................................................................... 57
13.3.7 Press [7] for RF Menu ........................................................................................................................................................ 57
13.3.7.1 Adding RF ID Codes .......................................................................................................................................................... 57
13.3.7.2 Testing RF Devices ............................................................................................................................................................. 58
13.3.7.3 Viewing/Removing RF ID Codes ....................................................................................................................................... 59
13.3.8 Press [8] for Keypad Program ........................................................................................................................................... 59
13.3.9 Press [9] Program Key ....................................................................................................................................................... 59
13.3.10 Exiting the Installer’s Menu ................................................................................................................................................ 60
13.3.11 Press [0] Call for Service Details ....................................................................................................................................... 61
14.0 Installation Label .............................................................................................................................................................. 62
15.0 Terminal Quick Reference ............................................................................................................................................... 64
16.0 Troubleshooting ................................................................................................................................................................ 65
16.1 Introduction ......................................................................................................................................................................... 65
16.1.1 Arming Issues ..................................................................................................................................................................... 65
16.1.2 Point Issues ........................................................................................................................................................................ 65
16.1.3 Command Center Issues ................................................................................................................................................... 66
16.1.4 Programming Issues .......................................................................................................................................................... 66
16.1.5 Miscellaneous Issues ......................................................................................................................................................... 66