Bosch radlonlcs D6412 - Page 6

Page 645349D © 2002 Radionics
D6412/D4412 Installation Guide
D6412/D4412
Figures
Figures
Figure 1: System Configuration ........................................................................................................................................................ 10
Figure 2: Enclosure Mounting ........................................................................................................................................................... 17
Figure 3: Installer Switch ................................................................................................................................................................... 18
Figure 4: System Status LED ........................................................................................................................................................... 22
Figure 5: On-Board Outputs.............................................................................................................................................................. 24
Figure 6: RJ31X/RJ38X Wiring......................................................................................................................................................... 25
Figure 7: System Status LED ........................................................................................................................................................... 25
Figure 8: Ground Start....................................................................................................................................................................... 27
Figure 9: Typical Two-Wire Smoke Detector Wiring ....................................................................................................................... 28
Figure 10: Typical Four-Wire Smoke Detector Wiring .................................................................................................................... 29
Figure 11: Sensor Loop 1 Wiring ...................................................................................................................................................... 29
Figure 12: Single Point Sensor Loop Wiring ................................................................................................................................... 29
Figure 13: On-board Doubled Point Sensor Loop Wiring ............................................................................................................... 30
Figure 14: Installing the DX2010 in D203 Enclosure ...................................................................................................................... 34
Figure 15: Installing the DX2010 in the Panel’s Enclosure............................................................................................................. 35
Figure 16: Optional Enclosure Mounting Locations for the DX2010 .............................................................................................. 35
Figure 17: Wiring the DX2010 to the D6412/D4412 ....................................................................................................................... 36
Figure 18: Wiring the DX2010 for External Power Supply .............................................................................................................. 37
Figure 19: Auxiliary Output Connections ......................................................................................................................................... 37
Figure 20: DX2010 Tamper Input Wiring ......................................................................................................................................... 38
Figure 21: DX2010 Sensor Loop Wiring, Single Loop Configuration ............................................................................................ 38
Figure 22: DX2010 Sensor Loop Wiring, Doubled Loop Configuration ......................................................................................... 39
Figure 23: DX2010 DIP Switch Configuration.................................................................................................................................. 40
Figure 24: DX2010 Status LED ........................................................................................................................................................ 40
Figure 25: PO 1 Wiring...................................................................................................................................................................... 41
Figure 26: PO 2 - PO 4 Wiring.......................................................................................................................................................... 41
Figure 27: DX3010 - Control Panel Enclosure Side Mounting ....................................................................................................... 43
Figure 28: Installing the DX3010 in a Remote Enclosure ............................................................................................................... 43
Figure 29: Wiring the DX3010 to the D6412/D4412 ....................................................................................................................... 44
Figure 30: Wiring for External Power Supply................................................................................................................................... 45
Figure 31: DX3010 Address DIP Switches ...................................................................................................................................... 45
Figure 32: Command Center DIP Switch Orientation ..................................................................................................................... 46
Figure 33: Wiring Command Centers to the D6412/D4412............................................................................................................ 47
Figure 34: External Power for Command Centers .......................................................................................................................... 48
Figure 35: Keyswitches ..................................................................................................................................................................... 49
Figure 36: SDI Device Wiring ........................................................................................................................................................... 50
Figure 37: External Power for SDI Devices ..................................................................................................................................... 51
Figure 38: DX4010 RS-232 Serial Interface Module ....................................................................................................................... 51
Figure 39: DX4010 Power Connections........................................................................................................................................... 52
Figure 40: Creating a RAM IV Direct Connection............................................................................................................................ 53
Figure 41: DX4010 P2/P3 Jumper Pin Settings .............................................................................................................................. 53
Figure 42: DX4010 DIP Switch Orientation...................................................................................................................................... 54
Figure 43: DX4010 DB9 Connector Layout ..................................................................................................................................... 54
Figure 44: Installer’s Keypad ............................................................................................................................................................ 55
Figure 45: Installer Switch................................................................................................................................................................. 56
Figure 46: Adding RF ID Codes Menu Display................................................................................................................................ 57
Figure 47: RF ID Code Display......................................................................................................................................................... 57
Figure 48: Test RF Devices Display ................................................................................................................................................. 58
Figure 49: RF Device Test Status Display ....................................................................................................................................... 58
Figure 50: RF ID Code Display......................................................................................................................................................... 59
Figure 51: PK32 to D6412/D4412 Connections .............................................................................................................................. 60