12
Names of Things and What They Do
20.
REC/PLAY/OVERDUB Pedal
• This switches between recording, playback, and overdubbing
for the currently selected phrase. With each press of the pedal,
the next function in the sequence is selected, as shown below.
“About Recording, Playback, and Overdubbing” (p. 30)
• You can press the pedal after recording to immediately start
overdubbing.
“Overdubbing Immediately After Recording (REC Pedal Action)”
(p. 69)
• Pressing this pedal in Patch select mode switches the RC-50 to
the next lower patch number.
“Switching Patches with the Pedals (Patch Select Mode)” (p. 33)
REC/PLAY/OVERDUB Indicator
This indicates the status of the phrase selected with the
PHRASE 1/2/3 pedals (the current phrase).
The indicator also indicates a number of other conditions. For
more details, refer to “Correspondence Between the Indicators
and Operational Status” (p. 89)
21.
STOP Pedal
• This stops recording, playback, and overdubbing for the
currently selected phrase.
“About Recording, Playback, and Overdubbing” (p. 30)
• Pressing this pedal in Patch Select mode switches the RC-50 to
the next higher patch number.
“Switching Patches with the Pedals (Patch Select Mode)” (p. 33)
• When the pedal is held down for at least two seconds, the
recording of the currently selected phrase is erased.
22.
TEMPO Pedal
Press this to change the patch tempo. You can adjust the tempo
by tapping the pedal several times; the tempo is set to the
interval between each tap.
You can also use the TAP TEMPO button instead of this pedal
to change tempos.
“Setting the Patch Tempo” (p. 45)
• Holding down this pedal for at least two seconds switches the
RC-50 to Patch Select mode. Pressing the pedal again switches
the patch and returns the Play screen to the display.
“Switching Patches with the Pedals (Patch Select Mode)” (p. 33)
TEMPO Indicator
This flashes in time with the tempo.
23.
UNDO/REDO Pedal
• Pressing this once allows you to restore (undo) the recorded or
overdubbed phrase to its state prior to the recording or
overdub.
• Pressing the pedal again after an undo has been carried out
allows you to switch the phrase back to the way it was after the
record/overdub (redo).
• In Patch Select mode, pressing the pedal returns the Play screen
to the display without switching the patch.
UNDO/REDO Indicator
Lights when a redo is available as an option.
24.
PHRASE 1/2/3 Pedals
• Press these to select the phrase (Phrase 1, 2, or 3) to be recorded
or played back.
• Holding down a PHRASE pedal for at least two seconds in
Multi mode while the phrase is stopped switches on Simul-Start
for that phrase.
A phrase with Simul-Start set to ON will start playing back
simultaneously the instant the REC/PLAY/OVERDUB pedal is
pressed only if the phrase already material recorded to it.
Holding down the pedal again for at least two seconds switches
the Simul-Start setting to OFF again.
• In Multi mode, simultaneously pressing the PHRASE 2 pedal
and PHRASE 3 pedal plays back or stops all of the phrases.
PHRASE 1/2/3 Indicators
The left (orange) indicator indicates the currently selected
phrase. The indicator flashes when that phrase is on hold as the
next phrase to be played. The right indicator indicates the status
of the currently selected phrase.
The indicator flashes when the phrase is the next phrase to be
played or when the phrase is in recording standby (or playback
standby).
The indicator flashes rapidly when Auto Recording (p. 47) is set
to ON.
The indicator also indicates a number of other conditions.
For more details, refer to “Correspondence Between the
Indicators and Operational Status” (p. 89)
When the phrase has
not been recorded
Recording
→
Playback
→
Overdubbing
→
Playback
→
...
When using a recorded
phrase
Playback
→
Overdubbing
→
Playback
→
...
Currently recording Red
Playing back Green
Overdubbing Orange
Currently recording Red
Playing back Green
Overdubbing Orange
RC-50_e.book 12 ページ ２００９年４月１０日 金曜日 午後１時１７分
To Next Page
Loading...
