65
Chapter 6
Pedal Operations in Single Mode
To record to a blank phrase, make the phrase you want to record to
the current phrase and then press the REC/PLAY/OVERDUB pedal.
You can have recording start automatically at the same time
performance on a musical instrument begins. For more detailed
information, refer to “Simultaneously Starting Recording When
Sounds Are Input (Auto Recording)” (p. 47).
When you press a PHRASE pedal other than the one for the current
phrase during recording, the selected phrase becomes the new
current phrase, and recording or playback of that phrase starts.
Recording starts if the phrase is blank, playback starts if it is a
recorded phrase.
You cannot change the tempo, for example using the TEMPO
pedal or [TAP TEMPO], while recording of the phrase is in
progress.
To play back a recorded phrase, make the phrase that you want to
play back the current phrase, then press the REC/PLAY/OVERDUB
pedal.
When a phrase is set to ONE SHOT (p. 52), then each time the REC/
PLAY/OVERDUB pedal is pressed during playback, the phrase
willstart playing from the beginning again.
You can also set Phrase Change mode (p. 49) to IMMEDIATE so
that the phrase will start playing immediately from the
beginning each time you press the PHRASE pedal.
You can change the patch tempo while playback is in progress with
the TEMPO pedal or [TAP TEMPO].
If Tempo Sync is set to ON in the phrase, you can then control the
phrase’s playback speed.
The manner in which phrases are switched when a PHRASE pedal
other than that for the current phrase is pressed differs according to
the Phrase Change Mode setting.
When Phrase Change Mode is Set to LOOP END
When you press a PHRASE pedal other than the one for the current
phrase, the orange and green or red indicators for the pressed
PHRASE pedal flash, indicating that, if left without further changes,
recording/playback of the selected phrase will begin at the same
time playback of the current phrase ends.
If you press the PHRASE pedal for the current phrase (with the lit
orange indicator) while these indicators are flashing, the indicators
stop flashing, and playback of the current phrase continues as is.
When Phrase Change Mode is Set to IMMEDIATE
When you press a PHRASE pedal other than the one for the current
phrase, the selected phrase becomes the new current phrase, and
recording or playback of that phrase starts. Recording starts if the
phrase is blank, playback starts if it is a recorded phrase.
When overdubbing to a recorded phrase, use the following procedure.
You cannot overdub when the phrase is set to ONE SHOT (p.
52).
1.
Set the phrase you want to overdub as the current phrase.
2.
While playing back the phrase, press the REC/PLAY/OVERDUB
pedal.
When you press a PHRASE pedal other than the one for the current
phrase during overdubbing, the RC-50 switches to the next phrase
according to the Phrase Change Mode (p. 49) settings.
When Phrase Change Mode is Set to LOOP END
When you press a PHRASE pedal other than the one for the current
phrase, the orange and red or green indicators for the pressed
PHRASE pedal flash, while overdubbing of the current phrase
switches to playback, and recording/playback of the selected phrase
will begin at the same time playback of the current phrase ends.
If you press the PHRASE pedal for the current phrase (with the lit
orange indicator) while these indicators are flashing, the indicators
stop flashing, and playback of the current phrase continues as is.
When Phrase Change Mode is Set to IMMEDIATE
When you press a PHRASE pedal other than the one for the current
phrase, the selected phrase becomes the new current phrase, and
recording or playback of that phrase starts. Recording starts if the
phrase is blank, playback starts if it is a recorded phrase.
• You cannot overdub a phrase when the phrase is set to ONE
SHOT. Pressing the REC/PLAY/OVERDUB pedal during
playback starts playback again from the beginning of the phrase.
• You cannot change the tempo, for example using the TEMPO
pedal or [TAP TEMPO], while overdubbing is in progress.
Starting Recording and
Operations During Recording
Switching Phrases with the PHRASE Pedals
Starting Playing and
Operations During Playing
Playing Back One Shot Phrases Continuously
Adjusting the Patch Tempo
Switching Phrases with the PHRASE Pedals
Operations at the Start of Overdubbing
and During Overdubbing
Switching Phrases with the PHRASE Pedals
RC-50_e.book 65 ページ ２００９年４月１０日 金曜日 午後１時１７分
To Next Page
Loading...
