31
About Recording, Playback, and Overdubbing
Chapter 2
If the current phrase has material recorded to it, pressing the REC/
PLAY/OVERDUB pedal in the Play screen starts playback of the
phrase.
Number of Phrases That Can Be
Played Back Simultaneously
In Multi mode, you can play back all three phrases simultaneously.
In Single mode, only the current phrase is played back.
To Confirm That the RC-50 is
Currently Playing Back
During playback, the green indicator on each PHRASE pedal lights.
In addition, the green indicator on the REC/PLAY/OVERDUB
pedal lights when the current phrase is being played back.
To Switch Playback-Related Operations
You can make the following settings with the RC-50 to switch among
the different types of playback tasks (settings are common to both
Single mode and Multi mode).
●
Playing back while fading in
→
“Start Mode” (p. 52)
●
Adjusting the fade-in speed
→
“Fade-Out Time/Fade-In Time” (p. 49)
●
Adjusting the phrase panning
→
“Pan” (p. 53)
●
Having phrases play only once
→
“One Shot” (p. 52)
●
Playing back in the opposite direction
→
“Reverse” (p. 52)
●
Synchronizing playback of the phrase to the patch tempo
→
“Tempo Sync” (p. 53)
●
Switching the output for the phrase sounds
→
“Output Select” (p. 53)
The following operations are also possible in Multi Mode.
●
Simultaneously starting playback of desired phrases
→
“Playing Multiple Phrases Simultaneously (Simul-Start)”
(p. 50)
●
Starting and stopping playback of all phrases simultaneously
→
“All Start/All Stop” (p. 61)
If the current phrase has material recorded to it, you can layer
additional recordings onto the phrase as it plays back by pressing
the REC/PLAY/OVERDUB pedal while playback is in progress.
This is called “overdubbing.”
Repeatedly overdubbing over the length of the phrase allows you to
create dense, thicker phrases each time you layer a newly recorded
phrase.
You cannot overdub when the phrase is set to ONE SHOT (p.
52).
Number of Phrases That Can Be
Overdubbed Simultaneously
Only the current phrase can be overdubbed. If you overdub on a
phrase other than the current phrase, the current phrase is switched
and overdubbing is conducted on the next phrase.
You cannot simultaneously overdub to multiple phrases.
About Tempos During Overdubbing
Overdubbing is carried out at the tempo in effect immediately
preceding the overdubbing.
You cannot change the RC-50's tempo while overdubbing is in
progress. In cases such as during performances synchronized to
the operations of an external MIDI device, the RC-50's tempo
cannot be changed even if the tempo of the external MIDI
device is changed. The change is executed immediately after
overdubbing is finished.
To Confirm That the RC-50 is Currently
Overdubbing
During overdubbing, the REC/PLAY/OVERDUB pedal indicator
and the orange indicator on the PHRASE pedal corresponding to the
current phrase are lit.
Phrase Length That Can Be Overdubbed
The phrase length that you can overdub is the same as the length of
whatever phrase you are overdubbing.
When Loop Sync is on while the RC-50 is in Multi mode,
overdubbing of a length equivalent to that of the phrase having
the longest playback time among those already recorded can be
carried out.
To Switch Overdubbing-Related Operations
You can make the following settings with the RC-50 to switch among
the different types of overdubbing tasks (settings are common to
both Single mode and Multi mode).
●
Recording while muting the sounds localized at the center
→
“AUX Center Cancel” (p. 48)
●
Recording with the tone adjusted for use with guitar amps
→
“AUX & MIC Flat Amp Simulator” (p. 48)
Playback
Overdubbing
RC-50_e.book 31 ページ ２００９年４月１０日 金曜日 午後１時１７分
To Next Page
