Braun Aesculap Acculan 4 User Manual (English)

Other manuals for Braun Aesculap Acculan 4

Questions and Answers:

R
Robert GreenAug 31, 2025
Why does my Braun Medical Equipment product become too hot?
- C
  Christopher RobertsonSep 1, 2025
  If your Braun Medical Equipment product becomes too hot, it could be due to several reasons. It may be caused by excessive use, so follow the operating instructions. The attachment may be defective, so follow the operating instructions and lubricate the attachment before every sterilization. If it was damaged by a fall, have the manufacturer repair the attachment. A blunt tool can also cause overheating, so change the tool. Insufficient power can be a factor; use serrated tools only in clockwise mode. Also, check if the attachment is defective and follow the operating instructions. Replace blunt tools.
S
Samuel GarciaSep 12, 2025
What to do if the tool on my Braun Aesculap Acculan 4 won't attach or detach?
- T
  Tina PerezSep 12, 2025
  If the tool on your Braun Medical Equipment does not attach or detach, ensure you are using a tool that is compatible with the attachment. If the tool connector is deformed or defective, use a new tool. If the coupling on the attachment is deformed or defective, have the manufacturer repair the attachment. A dirty tool coupling can also cause this issue; try cleaning the tool or using a new one, and also clean the attachment.
Z
Zachary MorenoAug 30, 2025
Why Braun Aesculap Acculan 4 Medical Equipment dermatome blade has insufficient cutting performance?
- J
  Jessica SmithAug 30, 2025
  If the dermatome blade on your Braun Medical Equipment has insufficient cutting performance, the dermatome blade may be blunted, so replace it. Also, the dermatome may need to be adjusted, so have the manufacturer repair the product.
H
Haley EvansSep 13, 2025
What to do if my Braun Aesculap Acculan 4 becomes too hot?
- A
  Amanda ScottSep 13, 2025
  If your Braun Medical Equipment becomes too hot, several factors could be responsible. Excessive use might be the cause, so ensure you are following the operating instructions. A defective attachment drive or ball bearings can also cause overheating; in this case, follow the operating instructions for preparation and care, and consider lubricating the attachment before sterilization. If the product has been damaged from a fall, or if the attachment is defective, have it repaired by the manufacturer. Other potential causes include using a blunt tool (change the tool), insufficient power (use serrated tools only in clockwise mode).
S
scottsusanSep 12, 2025
What to do if the oil spray adapter is not attachable to my Braun Aesculap Acculan 4 Medical Equipment?
- E
  ejuarezSep 12, 2025
  If the oil spray adapter is not attachable to your Braun Medical Equipment, make sure you are using the compatible oil spray adapter for GA344.
D
Dustin LinSep 16, 2025
What to do if Kirschner wire is not turning in my Braun GB641R Medical Equipment?
- J
  Jason GomezSep 16, 2025
  If the Kirschner wire is not turning in your Braun GB641R Medical Equipment, first, ensure that the Kirschner wire chuck is set correctly by adjusting the sleeve to the right Kirschner wire diameter. Also, make sure the clamping lever is closed. If it is open, close it. Finally, ensure that you are pulling back the clamping lever forcefully and holding it.
T
tristanmasseyAug 27, 2025
What to do if lid cannot be attached or removed from Braun Aesculap Acculan 4 Medical Equipment?
- H
  Holly WongAug 27, 2025
  If the lid of your Braun Medical Equipment cannot be attached or removed, it might be because the lid is not compatible. Use the compatible lid for GA340/GA341. The lid could also be deformed or defective, or the connection to the product could be deformed or defective, in which case you should have the manufacturer repair the lid or product.
L
leahstephensonAug 27, 2025
Why Braun Medical Equipment has loud running noise?
- U
  ugonzalezAug 27, 2025
  A loud running noise in your Braun Medical Equipment may be due to a defective product drive or ball bearings. In this case, follow the operating instructions for preparation and care, lubricate the product before every sterilization and have the manufacturer repair the product.
D
Devin LloydAug 26, 2025
What to do if speed control knob not working in Braun Aesculap Acculan 4?
- A
  Amy WilliamsAug 26, 2025
  If the speed control knob on your Braun Medical Equipment isn't working, first check if the product is in a locked OFF position and turn the safety catch to the ON position. If that doesn't work, the speed control knob may be stuck or defective, requiring repair by the manufacturer.
S
Steven ThomasAug 25, 2025
Why Braun Aesculap Acculan 4 has insufficient power?
- R
  Ryan Brown PhDAug 26, 2025
  Insufficient power in your Braun Medical Equipment could stem from a defective product, in which case you should follow the operating instructions for preparation and care, lubricate the product before sterilization, and have the manufacturer repair it. It could also be due to a large amount of heat generated after a short time, so follow the operating mode instructions and have the manufacturer repair the product. A blunt tool can also cause this issue; if so, change the tool.