To Next PageTo Next PageWhat to do if speed control knob not working in Braun Aesculap Acculan 4?
If the speed control knob on your Braun Medical Equipment isn't working, first check if the product is in a locked OFF position and turn the safety catch to the ON position. If that doesn't work, the speed control knob may be stuck or defective, requiring repair by the manufacturer.
Why Braun Medical Equipment has loud running noise?
A loud running noise in your Braun Medical Equipment may be due to a defective product drive or ball bearings. In this case, follow the operating instructions for preparation and care, lubricate the product before every sterilization and have the manufacturer repair the product.
What to do if lid cannot be attached or removed from Braun Aesculap Acculan 4 Medical Equipment?
If the lid of your Braun Medical Equipment cannot be attached or removed, it might be because the lid is not compatible. Use the compatible lid for GA340/GA341. The lid could also be deformed or defective, or the connection to the product could be deformed or defective, in which case you should have the manufacturer repair the lid or product.
What to do if sterile funnel or battery removal device not attachable to Braun Aesculap Acculan 4 Medical Equipment?
If a sterile funnel or battery removal device cannot be attached to your Braun Medical Equipment, ensure you are using a compatible sterile funnel or battery removal device for GA340/GA341. If it is compatible, the sterile funnel or battery removal device may be deformed or defective, so change it. The battery shaft to the product might also be deformed or defective, requiring manufacturer repair.
What to do if battery cannot be inserted or removed from Braun Aesculap Acculan 4?
If you're unable to insert or remove the battery from your Braun Medical Equipment, ensure you are using the compatible battery for GA340/GA341. If the battery is compatible, the battery itself may be deformed or defective, requiring it to be repaired by the manufacturer. Alternatively, the battery shaft to the product could be deformed or defective, needing repair by the manufacturer.
Why dermatome blade not moving in Braun Medical Equipment?
If the dermatome blade in your Braun Medical Equipment is not moving, it's likely due to defective gearings. In this case, have the manufacturer repair the product.
Why is my Braun Aesculap Acculan 4 product not running?
Your Braun Medical Equipment might not be running due to several reasons: there may be no battery inserted, the battery may not be charged, or the battery could be defective. Also, check if the product is in a locked OFF position. In this case, turn the safety catch to the ON position. If none of these solutions work, the product itself may be defective, and you should have it repaired by the manufacturer.
Why cutting depth is uneven or deviating from setting in Braun Aesculap Acculan 4?
If the cutting depth is uneven or deviating from the setting on your Braun Medical Equipment, it may be because the skin grafts are uneven, too thick, or too thin. Have the manufacturer repair the product.
Why does my Braun Medical Equipment product become too hot?
If your Braun Medical Equipment product becomes too hot, it could be due to several reasons. It may be caused by excessive use, so follow the operating instructions. The attachment may be defective, so follow the operating instructions and lubricate the attachment before every sterilization. If it was damaged by a fall, have the manufacturer repair the attachment. A blunt tool can also cause overheating, so change the tool. Insufficient power can be a factor; use serrated tools only in clockwise mode. Also, check if the attachment is defective and follow the operating instructions. Replace blunt tools.
What to do if the tool does not attach or detach on Braun Aesculap Acculan 4?
If the tool does not attach or detach from your Braun Medical Equipment, ensure you are using a tool that is compatible with the attachment. If the tool connector is deformed or defective, use a new tool. Should the coupling on the attachment be deformed or defective, have the manufacturer repair the attachment. Also, the tool coupling might be dirty, so clean the tool or use a new one, and clean the attachment as well.
General| Brand | Braun |
|---|---|
| Model | Aesculap Acculan 4 |
| Category | Medical Equipment |
| Language | English |
