EasyManua.ls Logo

Cisco ONS 15454 - Page 235

Cisco ONS 15454
728 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
4-43
Cisco ONS 15454 Reference Manual, R7.0.1
OL-9217-01
Chapter 4 Optical Cards
4.18 4.18.2 Ports and Line Rates
The maximum bandwidth of the 15454_MRC-12 card is determined by the cross-connect card, as shown
in Table 4-19.
4.18.2 Ports and Line Rates
Each port on the 15454_MRC-12 card can be configured as OC-3/STM-1, OC-12/STM-4, or
OC-48/STM-16, depending on the available bandwidth and existing provisioned ports. Based on the
cross-connect card and slot limitations shown in Table 4-19, the following rules apply for various
synchronous transport signal (STS) available bandwidths. (Table 4-20 shows the same information in
tabular format.)
STS-12
Port 1 is the only port that is usable as an OC-12. If Port 1 is used as an OC-12, all other ports
are disabled.
Ports 1, 4, 7, and 10 are the only ports usable as OC-3. If any of these ports is used as an OC-3,
Ports 2, 3, 5, 6, 8, 9, 11, and 12 are disabled.
STS-48
Port 1 is the only port usable as an OC-48. If Port 1 is used as an OC-48, all other ports are
disabled.
Ports 1, 4, 7, and 10 are the only ports usable as OC-12.
If Port 4 is used as an OC-12, Ports 2 and 3 are disabled.
If Port 7 is used as an OC-12, Ports 5, 6, and 8 are disabled.
If Port 10 is used as an OC-12, Ports 9, 11, and 12 are disabled.
Any port can be used as an OC-3 as long as all of the above rules are followed.
STS-192
Ports 1, 4, 7, and 10 are the only ports usable as OC-48.
If Port 4 is used as an OC-48, Ports 2 and 3 are disabled.
If Port 7 is used as an OC-48, Ports 5, 6, and 8 are disabled.
If Port 10 is used as an OC-48, Ports 9, 11, and 12 are disabled.
If Port 4 is used as an OC-12, Ports 2 and 3 can be used as an OC-12 or OC-3.
If Port 7 is used as an OC-12, Ports 5, 6, and 8 can be used as an OC-12 or OC-3.
If Port 10 is as used as an OC-12, Ports 9, 11, and 12 can be used as an OC-12 or OC-3.
If Port 4 is used as an OC-3, Ports 2 and 3 can be used as an OC-3 or OC-12.
If Port 7 is used as an OC-3, Ports 5, 6, and 8 can be used as an OC-3 or OC-12.
Table 4-19 Maximum Bandwidth by Shelf Slot for the 15454_MRC-12 in Different Cross-Connect
Configurations
XC Card Type
Maximum Bandwidth
in Slots 1 through 4
and 14 through 17
Maximum Bandwidth
in Slots 5, 6, 12, or 13
XCVT OC-12 OC-48
XC10G/XC-VXC-10G OC-48 OC-192

Table of Contents

Other manuals for Cisco ONS 15454

Related product manuals