What to do if Columbus Instruments Treadmill belt does not turn?
If the treadmill belt isn't turning, there are several things you can check. First, make sure the belt speed is set to 06.0 M/M or higher. Ensure that the 'RUN/STOP' switch is in the 'RUN' position and that the motor cable is securely connected. If the belt is jammed to one side of the drive shaft, adjust the belt tension and manually turn the belt to loosen it.
Why is my Columbus Instruments Exer 3/6 Treadmill exercise belt pulling to one side?
If the exercise belt is pulling to one side of the drive shaft, the belt tension is likely unequal. Readjust the belt tension to correct this issue.
How to troubleshoot Columbus Instruments Treadmill if power indicator light does not turn on?
If the power indicator light doesn't turn on, check for a blown fuse, verify proper voltage at the AC receptacle, and replace any bad power cords.
What to do if the LCD of my Columbus Instruments Exer 3/6 Treadmill Controller is not working?
If the LCD of your Columbus Instruments Treadmill Controller is not lit continuously or doesn't display text, ensure the contrast knob is adjusted fully clockwise. If the issue persists, it may indicate a fault within the Treadmill Controller.
How to check the AC power cord on a Columbus Instruments Exer 3/6 Treadmill?
Make sure the AC power cord of your Columbus Instruments Treadmill is fully inserted into both the Treadmill Controller and the AC power outlet.
How do I check the serial cable connection on my Columbus Instruments Exer 3/6 Treadmill?
To check the serial cable between your host computer and the Columbus Instruments Treadmill's Computer Interface, ensure it's properly connected. When the computer sends information to the CI-Bus, the transmit indicator (top left yellow LED on the “CONTROLLER” port of the Computer Interface) should flash briefly.
How to check the power supply for the Columbus Instruments Treadmill Computer Interface?
Verify that the power plug is correctly installed in the Computer Interface and that the power supply is properly inserted into the AC power outlet for your Columbus Instruments Treadmill.
How to check the RJ-45 cable on a Columbus Instruments Exer 3/6?
Ensure the RJ-45 cable between the Computer Interface and the Treadmill Controller of your Columbus Instruments Treadmill is fully inserted, with the connector locking tab snapped into the jack.
How to check the power indicator on the Columbus Instruments Treadmill Computer Interface?
Ensure that the top right green LED on the “CONTROLLER” port of the Computer Interface is continuously lit on your Columbus Instruments Treadmill.
Provides an overview of the Exer 3/6 Treadmill's design, capabilities, and components.
Step-by-step guide for installing the Treadmill Software from CD-ROM.
Instructions for manually installing the CI-Bus Hub USB communication drivers.
Provides instructions for assembling the main treadmill unit.
Instructions for assembling and attaching the Downhill Running Adapter.
Details the items and steps for assembling the Air-Puff Stimulus system.
Guide for connecting the CI-Bus Hub, network cable, and treadmill controller.
Procedure to initialize the controller for standalone operation, preventing unwanted startup.
Accessing and navigating the controller's user menu for settings and calibration.
Steps for loading animals onto the treadmill and setting up shock stimulus.
Procedure to set up the Treadmill Controller for PC-controlled experiments.
Instructions for setting up the Treadmill Shock Detection unit.
Guide for setting up the Incline Controller for operation.
Steps to launch and initialize the Treadmill Software on the host computer.
Guide to setting up and running a single-speed or acceleration experiment.
Procedure to start a manual experiment and load animals.
Overview of running experiments with dynamic speed, acceleration, and incline profiles.
Steps to define experiment periods with speed, duration, incline, and shock.
Procedure to start a profile mode experiment and load animals.
Performs automatic belt speed and odometer distance calibration.
Starts and initializes the Treadmill Software, scanning for devices.
Tips for identifying and resolving hardware-related issues.
General| Running Surface | 18 x 48 in (46 x 122 cm) |
|---|---|
| Speed | 0.5 - 15 mph (0.8 - 24 kmph) |
| Elevation | 0 - 25% |
| User Weight Capacity | 400 lbs (181 kg) |
| Speed Range | 0.5 - 15 mph (0.8 - 24 kmph) |
| Incline Range | 0 - 25% |
| Belt Size | 18 x 48 in (46 x 122 cm) |
| Control | Computer Interface |
| Data Output | RS232 |
| Shock Grid | Optional |
| Stimulus Grid | Optional |
To Next Page
