Eaton Network-M3 - Page 266

SNMP traps
Information – 266
Alarm oid at :
.1.3.6.1.2.1.33.1.6.3.x
Description when trap 3 Description when trap 4
.1.3.6.1.2.1.33.1.6.3.8 Power overload No power overload
.1.3.6.1.2.1.33.1.6.3.9 Bypass mode No more on bypass
.1.3.6.1.2.1.33.1.6.3.10 Bypass not available Bypass available
.1.3.6.1.2.1.33.1.6.3.13 Battery charger fault Battery charger OK
.1.3.6.1.2.1.33.1.6.3.14 Not powered Powered (Protected or Not protected)
.1.3.6.1.2.1.33.1.6.3.16 Fan fault Fan OK
.1.3.6.1.2.1.33.1.6.3.17 Battery fuse fault
Rectifier fuse fault
Inverter fuse fault
Battery fuse OK
Rectifier fuse OK
Inverter fuse OK
.1.3.6.1.2.1.33.1.6.3.18 Internal failure End of internal failure
.1.3.6.1.2.1.33.1.6.3.20 Communication lost Communication recovered
.1.3.6.1.2.1.33.1.6.3.23 Shutdown imminent Shutdown canceled
7.6.1.2 Xups Mib traps
This information is for reference only.
Trap oid :
.1.3.6.1.4.1.534.1.11
.4.1.0.x
Trap message at
oid :
.1.3.6.1.4.1.534.1.1
1.3.0
Code HID (For UPS 5P, 5PX, 9SX,
9PX, 9xPM, 9xE, 9xPS)
Code XCP (For UPS Blade,
9395, 9395P, 9395C, 9x55)
.1.3.6.1.4.1.534.1.11
.4.1.0.3
Battery discharging 603 2168
.1.3.6.1.4.1.534.1.11
.4.1.0.4
Battery low 604 2056, 2369, 2387
.1.3.6.1.4.1.534.1.11
.4.1.0.5
No more on battery 104, 106 2067
.1.3.6.1.4.1.534.1.11
.4.1.0.6
Battery OK 604 2056, 2369, 2387
.1.3.6.1.4.1.534.1.11
.4.1.0.7
Power overload 208, 306, 705, 80E, 810, 81f, 820,
821, 808
2102, 2103, 2104, 2325, 2027,
2025, 2159, 2160, 2162, 2163,
2164, 2165, 2166, 2167, 2323,
2342, 2380, 2381, 2382
.1.3.6.1.4.1.534.1.11
.4.1.0.8
Internal failure 002, 010, 105, 300, 301, 302,
303, 305, 400, 621, 80d, 814,
816
2000, 2001, 2047, 2051, 2063,
2070, 2077, 2089, 2135, 2147,
2224, 2229, 2365, 2384, 2364,
2002, 2026, 2028, 2029, 2112,
2031, 2048, 2068
.1.3.6.1.4.1.534.1.11
.4.1.0.9
Battery totally
discharged
2126
.1.3.6.1.4.1.534.1.11
.4.1.0.10
Inverter internal
failure
704 2031