Endress+Hauser Proline Promag W 800 - Page 4

Table of contents Proline Promag W 800
4 Endress+Hauser
7.8 Special connection instructions ............ 63
7.8.1 Connection examples ............. 63
7.9 Ensuring the degree of protection .......... 63
7.9.1 Degree of protection IP68, type 6P
enclosure or IP66/67, type 4X
enclosure, Proline 800 - Standard ... 63
7.9.2 Degree of protection IP68, type 6P
enclosure, with "Cust-potted" option,
Proline 800 - Advanced (separate
version) ...................... 63
7.9.3 Degree of protection IP66/67, type
4X enclosure, Proline 800 -
Advanced ..................... 64
7.10 Post-connection check .................. 64
8 Operation options ................. 66
8.1 Overview of operation options ............ 66
8.2 Access to the operating menu via the
SmartBlue app ........................ 66
9 System integration ................ 68
9.1 Overview of device description files ......... 68
9.1.1 Current version data for the device ... 68
9.1.2 Operating tools ................. 68
10 Commissioning .................... 69
10.1 Post-mounting and post-connection check ... 69
10.2 Preparatory steps ...................... 69
10.2.1 Install the SmartBlue App ......... 69
10.2.2 Connect the SmartBlue App to the
device ........................ 69
10.3 Configuring the measuring device .......... 69
10.4 Protecting settings from unauthorized access . 69
10.4.1 Write protection via access code ..... 69
10.4.2 Write protection via write protection
switch ........................ 70
11 Operation ......................... 72
11.1 Wake on Touch ....................... 72
11.2 Adapting the measuring device to the process
conditions ........................... 73
11.3 Performing a totalizer reset .............. 73
11.4 Disabling the Bluetooth interface .......... 73
11.5 Enabling the software option ............. 73
11.5.1 "Software configuration" submenu ... 73
11.6 Updating the firmware .................. 74
11.7 Checking, verifying or calibrating the
measuring device ...................... 74
12 Diagnosis and troubleshooting ..... 75
12.1 General troubleshooting ................. 75
12.2 Diagnostic information on local display ...... 77
12.2.1 Diagnostic message .............. 77
12.3 Adapting the diagnostic information ....... 78
12.3.1 Adapting the diagnostic behavior .... 78
12.4 Overview of diagnostic information ........ 78
12.5 Pending diagnostic events ............... 81
12.6 Diagnostics list ....................... 82
12.7 Event logbook ........................ 82
12.7.1 Reading out the event logbook ...... 82
12.7.2 Filtering the event logbook ........ 83
12.7.3 Overview of information events ..... 83
12.8 Resetting the measuring device ........... 84
12.9 Device information .................... 84
12.10 Firmware history ...................... 85
13 Maintenance ...................... 86
13.1 Maintenance work ..................... 86
13.1.1 Exterior cleaning ................ 86
13.1.2 Interior cleaning ................ 86
13.1.3 Replacing the batteries ........... 86
13.2 Measuring and test equipment ............ 91
13.3 Endress+Hauser services ................ 91
14 Repair ............................ 92
14.1 General notes ........................ 92
14.1.1 Repair and conversion concept ...... 92
14.1.2 Notes for repair and conversion ..... 92
14.2 Spare parts .......................... 92
14.3 Endress+Hauser services ................ 92
14.4 Return .............................. 92
14.5 Disposal ............................ 93
14.5.1 Removing the measuring device ..... 93
14.5.2 Disposing of the measuring device ... 93
14.5.3 Battery disposal ................ 93
15 Accessories ....................... 94
15.1 Device-specific accessories ............... 94
15.1.1 For the Proline 800 transmitter -
Standard ...................... 94
15.1.2 For the Proline 800 - Advanced
transmitter .................... 94
15.1.3 For the sensor .................. 94
15.2 Service-specific accessories ............... 95
16 Technical data .................... 96
16.1 Application .......................... 96
16.2 Function and system design .............. 96
16.3 Input ............................... 96
16.4 Output ............................. 98
16.5 Power supply ........................ 100
16.6 Performance characteristics ............. 104
16.7 Mounting .......................... 105
16.8 Environment ........................ 105
16.9 Process ............................ 107
16.10 Mechanical construction ............... 110
16.11 Operability ......................... 117
16.12 Certificates and approvals .............. 117
16.13 Application packages .................. 119
16.14 Accessories ......................... 119
16.15 Supplemental documentation ............ 120