ESAB 100i - Page 135

Manual 0560956430 135 TORCH DATA 100i-400i
Mild Steel
Flow Rates (SLPM / SCFH)
70A
O₂ Air
Preow
- / - 44 / 94
O₂ Plasma / Air Shield
Culow
10 / 21 25 / 52
Electrode
Shield Cap
Tip
Shield Gas
Distributor
Plasma Gas
Distributor
Cartridge
Shield Cup
This Art Is For Reference ONLY
Art # A-07958_AB
Shield Cup Shield Cap
Shield Gas
Distributor
Tip Plasma Gas Distributor Electrode Cartridge
0559211201 0559210043 0559210071 0559210023 0559210061 0559210002 0559211200
Manual Gas Control Advanced Torch Height Control (THC) Basic THC CNC Control
Material
Thickness
Pre Flow
Pressure
(Air)
Cut Flow Rates / Pressures
Arc
Voltage
Cut Height
THC
Pierce
Delay
Pierce
Ignion
Height
Elevaon
Height
Control
Delay
Pierce
Height
without
Elevaon
Travel
Speed
CNC
Moon
Delay
Max Kerf Width
@ Rec. Speed
Plasma (O₂) Shield (Air)
ga (in) inch (psi) Ball (psi) Ball (psi) (Volts) (in) ±0.005 (sec) (in) (in) (sec) (in) (ipm) (sec) (in)
16 - 0.060 46 35 120 41 120 143 0.070 0.1 0.080 0.040 1.0 0.100 300 0.1 0.073
14 - 0.075 46 35 120 41 120 145 0.100 0.1 0.090 0.060 1.0 0.120 250 0.1 0.072
12 - 0.105 46 55 120 60 120 147 0.100 0.2 0.090 0.060 0.9 0.120 225 0.2 0.078
10 - 0.135 46 55 120 60 120 148 0.100 0.2 0.100 0.080 0.9 0.150 180 0.2 0.071
- 3/16 0.188 46 55 120 60 120 149 0.115 0.4 0.125 0.120 0.7 0.200 130 0.4 0.077
- 1/4 0.250 46 55 120 60 120 151 0.120 0.5 0.125 0.120 0.6 0.200 100 0.5 0.083
Manual Gas Control Advanced Torch Height Control (THC) Basic THC CNC Control
Material
Thickness
Pre Flow
Pressure
(Air)
Cut Flow Rates / Pressures
Arc
Voltage
Cut Height
THC
Pierce
Delay
Pierce
Ignion
Height
Elevaon
Height
Control
Delay
Pierce
Height
without
Elevaon
Travel
Speed
CNC
Moon
Delay
Max Kerf Width
@ Rec. Speed
Plasma (O₂) Shield (Air)
(mm) (Bar) Ball (Bar) Ball (Bar) (Volts) (mm) ±0.1 (sec) (mm) (mm) (sec) (mm)
(mm/
min)
(sec) (mm)
1.5 3.2 35 8.3 41 8.3 143 1.7 0.1 2.0 1.0 1.0 2.5 7700 0.1 1.9
2 3.2 37 8.3 43 8.3 145 2.5 0.1 2.3 1.5 1.0 3.0 6270 0.1 1.8
2.5 3.2 51 8.3 56 8.3 147 2.5 0.2 2.3 1.5 0.9 3.0 5850 0.2 1.9
3 3.2 55 8.3 60 8.3 147 2.5 0.2 2.4 1.7 0.9 3.4 5220 0.2 1.9
4 3.2 55 8.3 60 8.3 148 2.7 0.3 2.8 2.5 0.8 4.4 4030 0.3 1.9
5 3.2 55 8.3 60 8.3 149 2.9 0.4 3.2 3.0 0.7 5.1 3190 0.4 2.0
6 3.2 55 8.3 60 8.3 151 3.0 0.5 3.2 3.0 0.6 5.1 2710 0.5 2.1
Marking
Pre Flow
Pressure
(N₂)
Marking Flow Rates /
Pressures
Arc
Voltage
Marking
Height
Pierce Ignion Height
THC and CNC
Delay
Control
Delay
Travel
Speed
Marking quality
degrades as
thickness
decreases.
16A Arc Current
Plasma (N₂) Shield (N₂)
Burn-through may
happen for thicknesses
< 1/16” (0.063”) /
1.6 mm.
(psi) /
(Bar)
Ball
(psi) /
(Bar)
Ball
(psi) /
(Bar)
(Volts)
(in) ±0.005 /
(mm) ±0.1
(in) ±0.005 / (mm) ±0.1 (sec) (sec)
(ipm) /
(mm/ min)
20 / 1.4 50
40 /
2.8
100
80 /
5.5
148 0.120 / 3.0 0.120 / 3.0 0 0.4
300 /
7620