ESAB 100i - Page 189

Manual 0560956430 189 TORCH DATA 100i-400i
Aluminum
Flow Rates (SLPM / SCFH)
300A Bevel Cut
H35 N₂
Preow
- / - 74 / 156
H35 Plasma / N₂ Shield
Culow
44 / 93 51 / 107
Electrode
Shield Retainer
Tip
Art # A-08567_AB
Plasma Gas
Distributor
Cartridge Assembly
This Art Is For Reference ONLY
Shield Cap
Shield Gas
Distributor
Shield Retainer Shield Cap
Shield Gas
Distributor
Tip Plasma Gas Distributor Electrode Cartridge
0559211211
< 1” / 0559210151
≥ 1” / 0559210153
0559210082 0559210130 0559210061 0559210111 0559211300
Manual Gas Control Advanced Torch Height Control (THC) Basic THC CNC Control
Eecve
Material
Thickness
Min.
Clearance
Pre Flow
Pressure
(N₂)
Cut Flow Rates / Pressures
Eecve Cut
Height
THC
Pierce
Delay
Pierce
Ignion
Height
Elevaon
Height
Control
Delay
Pierce
Height
without
Elevaon
Travel
Speed
CNC
Moon
Delay
Max Kerf Width
@ Rec. Speed
Plasma (H35) Shield (N₂)
inch (in) (psi) Ball (psi) Ball (psi) (in) (sec) (in) (in) (sec) (in) (ipm) (sec) (in)
0.250 0.080 20 120 100 NA 120 0.400 - 0.450 0.1 0.300 0.250 0.5 0.400 300 0.1 0.182
0.375 0.080 20 120 100 NA 120 0.400 - 0.450 0.2 0.300 0.250 0.4 0.400 275 0.2 0.186
0.500 0.080 20 120 100 NA 120 0.300 - 0.450 0.4 0.300 0.250 0.3 0.400 210 0.3 0.174
0.625 0.080 20 120 100 NA 90 0.300 - 0.450 0.6 0.250 0.300 0.2 0.350 140 0.4 0.169
0.750 0.080 20 120 100 NA 90 0.300 - 0.450 0.8 0.250 0.300 0.2 0.350 110 0.5 0.172
0.875 0.080 20 120 100 NA 90 0.300 - 0.450 1.0 0.300 0.250 0.2 0.400 95 0.6 0.183
1.000 0.080 20 120 100 NA 120 0.350 - 0.450 1.2 0.350 0.300 0.2 0.450 85 0.7 0.190
1.250 0.080 20 120 100 NA 120 0.400 - 0.450 1.6 0.400 0.400 0.2 0.500 60 0.8 0.205
1.500 0.080 20 120 100 NA 120 0.400 - 0.450 1.5 Edge Start 0.2 Edge 45 1.0 0.215
1.750 0.080 20 120 100 NA 120 0.400 - 0.450 0.4 Edge Start 0.2 Edge 35 0.4 0.226
2.000 0.080 20 120 100 NA 120 0.400 - 0.450 0.4 Edge Start 0.2 Edge 25 0.4 0.215
Manual Gas Control Advanced Torch Height Control (THC) Basic THC CNC Control
Eecve
Material
Thickness
Min.
Clearance
Pre Flow
Pressure
(N₂)
Cut Flow Rates / Pressures
Eecve Cut
Height
THC
Pierce
Delay
Pierce
Ignion
Height
Elevaon
Height
Control
Delay
Pierce
Height
without
Elevaon
Travel
Speed
CNC
Moon
Delay
Max Kerf Width
@ Rec. Speed
Plasma (H35) Shield (N₂)
(mm) (mm) (Bar) Ball (Bar) Ball (Bar) (mm) (sec) (mm) (mm) (sec) (mm)
(mm/
min)
(sec) (mm)
6 2.0 1.4 120 6.9 NA 8.3 10.2 - 11.4 0.1 7.6 6.4 0.5 10.2 7690 0.1 4.6
8 2.0 1.4 120 6.9 NA 8.3 10.2 - 11.4 0.2 7.6 6.4 0.4 10.2 7290 0.2 4.7
10 2.0 1.4 120 6.9 NA 8.3 9.8 - 11.4 0.2 7.6 6.4 0.4 10.2 6740 0.2 4.7
12 2.0 1.4 120 6.9 NA 8.3 8.2 - 11.4 0.4 7.6 6.4 0.3 10.2 5700 0.3 4.5
15 2.0 1.4 120 6.9 NA 6.8 7.6 - 11.4 0.5 6.7 7.3 0.2 9.2 4050 0.4 4.3
20 2.0 1.4 120 6.9 NA 6.2 7.6 - 11.4 0.9 6.7 7.2 0.2 9.3 2680 0.5 4.5
25 2.0 1.4 120 6.9 NA 8.0 8.7 - 11.4 1.2 8.7 7.5 0.2 11.3 2190 0.7 4.8
30 2.0 1.4 120 6.9 NA 8.3 9.8 - 11.4 1.5 9.8 9.5 0.2 12.4 1700 0.8 5.1
35 2.0 1.4 120 6.9 NA 8.3 10.2 - 11.4 1.5 Edge Start 0.2 Edge 1270 1.0 5.3
40 2.0 1.4 120 6.9 NA 8.3 10.2 - 11.4 1.2 Edge Start 0.2 Edge 1070 0.8 5.5
50 2.0 1.4 120 6.9 NA 8.3 10.2 - 11.4 0.4 Edge Start 0.2 Edge 670 0.4 5.5
BOLD TYPE indicates maximum piercing parameters. BOLD ITALIC indicates edge starts only.