Extron electronics DTP CrossPoint 4K Series - Page 177

DTP CrossPoint 4K Series Matrix Switchers • DSP SIS Commands 169
Command Function
SIS Command
(Host to Unit)
Response
(Unit to Host)
Additional description
Group masters
NOTES:
• See Group masters on page 119, for more information about audio group masters.
• A group must have assigned members for these commands to have an effect.
• For
X8$
, a positive (+) value is assumed unless a negative (-) value is specified.
• If entering a
X8$
value outside the valid range for the group or outside the soft limits, the DTP CrossPoint responds with an invalid
parameter (E13) error.
Set a group fader control
E
D
X8#
*
X8$
GRPM
}
GrpmD
X8#
*
X8$]
Set the group fader to a value of
X8$
.
Example:
E
D2*-293GRPM
}
GrpmD2*-293
]
Set the group 2 fader control to
-29.3dB.
Raise a group fader control
E
D
X8#
*
X8%
+GRPM
}
GrpmD
X8#
*
X8$]
Increase the level of the
X8#
group fader
by
X8%
dB.
Example:
E
D2*30+GRPM
}
GrpmD2*-263
]
Raise the group 2 fader 3dB (from
-29.3dB to -26.3dB, starting from the
level set in the Set a group fader control
example, above.
Lower a group fader control
E
D
X8#
*
X8%
-GRPM
}
GrpmD
X8#
*
X8$]
Decrease the level of the
X8#
group
fader by
X8%
dB.
View the group fader control level
E
D
X8#
GRPM
}
GrpmD
X8#
*
X8$]
In verbose modes 1 and 2, the response
is simplified to
X8$]
.
Mute a group mute control
E
D
X8#
*1GRPM
}
GrpmD
X8#
*1
]
Mute all blocks in group
X8#
.
Clear (unmute) a group mute control
E
D
X8#
*0GRPM
}
GrpmD
X8#
*0
]
Umute all blocks in group
X8#
.
View a group mute control mute
E
D
X8#
GRPM
} X8@]
Set soft limits
E
L
X8^
*
X8^
upper
*
X8^
lower
GRPM
}
Set the groups soft limits to
X8^
and
X8^
.
GrpmL
X8^
*
X8^
*
X8^]
Example:
E
L2*+60*-60GRPM
}
GrpmL2*60*–60
]
Set the upper soft limit for the group 2
fader to +6.0dB and the lower limit to
-6.0dB.
View soft limits
E
L
X8^
GRPM
}
GrpmL
X8^
*
X8^
*
X8^]
In verbose modes 0 and 1, the response
is simplified to
X8^
*
X8^]
.
View group type
E
P
X8#
GRPM
}
GrpmP
X8#
*
X8&]
Show the group type (
X8&
) for group
X8#
. In verbose modes 0 and 1, the
response is simplified to
X8&]
.
View group members
E
O
X8#
GRPM
} X8)
is the control or mix-point. In
verbose modes 0 and 1, the response is
simplified to
X8)
1
*
X8)
2
*...*
X8)
16
]
.
GrpmO
X8#
*
X8)
1
*
X8)
2
*...*
X8)
16
]
NOTE: X8) = Object ID (gain control or mix-point) See OID table, beginning on page 161.
X8# = Group master group number 01 – 32
X8$ = Group fader setting dB value, in 0.1 dB increments. The valid range depends on the type of gain block
X8% = Group fader increment dB value, in 0.1dB increments, to raise or lower a group fader
X8^ = Group fader soft limit dB value, in 0.1dB increments.
X8^ must be within the range for the gain block grouped in X8#.
X8& = Group type 6= gain 12 = mute