Extron electronics DTP CrossPoint 4K Series - Serial and IR Insertion Connections

DTP CrossPoint 4K Series Matrix Switchers • Installation 16
M
S/PDIF output (see figure 6 and figure 7 on the previous page) — Connect as
S/PDIF
OUT
S/PDIF device to this RCA jack to receive audio from the HDMI 6, 4, or 2 digital
stream (see S/PDIF output connector on page 23 to wire this connector).
N
DMP Expansion port and Link LED (see figure 6 and figure 7)—
EXP
LINK
Port — Connect an STP cable between this port and the Expansion port
on an optional Extron DMP 128 ProDSP Digital Matrix Processor. The
DMP 128 includes a shielded 1-foot cable. See Expansion Port Operation within the
DSP on page 146 for using the audio system scalability, expanded audio processing,
and signal routing functions). No setup is required; just connect the two devices.
LED — Lights to indicate that the port is connected to a compatible device.
Serial and IR Insertion Connections
RS-232 IR
Tx Rx Tx RxG
78
DTP CROSSPOINT 108 4K
OVER TP
INPUTS INPUTS
OUTPUTS
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
91
0
OVER TP
RS-232 IR
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
OVER TP
8
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
OVER TP
Tx Rx RTSCTS GTxRxG Tx Rx G
EXP
+48V
MIC/LINE
1
1
3
2
4
2
3
4
LINK
LAN 2
LAN 1
LAN 3
R
AUDIO OUTPUTS
AMP OUTPUT
CONTROL
1234G
DIGITAL I/OCOM 3COM 2
AUDIO INPUTS
COM 1
S
DMP EXPANSION
SGG
1
1
2
2
C34C
-S G+S+V
PWR OUT = 6W
1
LR
1
LR
3
LR
3
LR
5
LR
2
LR
4
LR
2
LR
4
LR
6
LR
IR/SERIAL eBUSRELAYS
1
CLASS 2 WIRING
70V
Tx Rx G
RESET
REMOTE
LAN
123456
1 2 3 4 5A 6A
XTP
DTP
HDBT
SIG LINK
OUT
5B 6B
XTP
DTP
HDBT
SIG LINK
OUT
6
S/PDIF
OUT
XTP
DTP
HDBT
7
SIG LINK
OUT
8
XTP
DTP
HDBT
SIG LINK
OUT
XTP
DTP
SIG LINK
IN
XTP
DTP
XTP
DTP
SIG LINK
IN
SIG LINK
IN
XTP
DTP
SIG LINK
IN
50-60 Hz
100-240V ~
3.0 A MAX
P P OO
Figure 8. Serial and IR Insertion Connections, 10x8 Matrix
50-60 Hz
100-240V ~ 1.6 A MAX
12
123456
3A 4A
4B
XTP
RESET
DTP
XTP
DTP
XTP
DTP
XTP
DTP
HDBT
HDBT
7
8
DTP CROSSPOINT 84 4K
INPUTS
OUTPUTS
3B
Tx Rx G
REMOTE
SIG LINK
OUT
SIG LINK
OUT
SIG LINK
IN
SIG LINK
IN
4
S/PDIF
OUT
RS-232 IR
RS-232 IR
Tx Rx Tx RxG
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
OVER TP
OVER TP
RS-232 IR
+48V
MIC/LINE
1
1
3
2
4
2
3
4
AUDIO OUTPUT
S
AUDIO INPUT
S
1
LR
1
R
3
LR
3
LLR
5
LR
2
LR
4
LR
2
LR
4
LR
6
LR
EXP
DMP EXPANSION
R
CONTROL
Tx Rx RTSCTS G
12
12
SGSG
C
34C+V
PWR OUT = 6W
+V D-S+S
Tx Rx G Tx Rx G1234G
COM 1 COM 3COM 2 DIGITAL I/O
LAN 1
LAN 2 LAN 3
IR/SERIAL RELAYS DIGITAL I/O
AMP OUTPUT
CLASS 2 WIRING
1
100V
P O
Figure 9. Serial and IR Insertion Connections, 8x4 Matrix
O
Over TP input ports — Connect serial RS-232 signals, modulated IR,
RS-232 IR
Tx Rx Tx RxG
signals or both, to these 3.5 mm, 5-pole captive screw connectors (ground
pin is shared) to insert bidirectional RS-232 and IR communications onto the
associated inputs (see Serial and IR port connectors on page 23 to wire
the cables).
The following table identifies the Over TP inputs by matrix size.
Matrix Inputs Matrix Inputs
10x8 7 through 10 All others 7 and 8
P
Over TP output ports — Connect serial RS-232 signals, modulated IR
RS-232 IR
Tx Rx Tx RxG
signals, or both, to these 3.5 mm, 5-pole captive screw connectors (ground
pin is shared) to insert bidirectional RS-232 and IR communications onto the
associated outputs (see Serial and IR port connectors to wire the cables).
The following table identifies the Over TP outputs by matrix size.
Matrix Outputs Matrix Outputs
10x8 5B, 6B, 7, 8 8x6 3B, 4B, 5, 6
8x4 3B, 4B 8x2 1B, 2B