Extron electronics DTP CrossPoint 4K Series - Audio Input and Output Connections

DTP CrossPoint 4K Series Matrix Switchers • Installation 15
Audio Input and Output Connections
1 2 3 4 5A 6A
XTP
RS-232 IR
Tx Rx Tx RxG
XTP
DTP
XTP
DTP
EXP
+48V
MIC/LINE
1
1
3
2
4
2
3
4
LINK
DTP
HDBT
123457 86
DTP CROSSPOINT 108 4K
OVER TP
AUDIO OUTPUTS
AUDIO INPUTS
DMP EXPANSION
INPUTS
INPUTS
OUTPUTS
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
XTP
DTP
XTP
DTP
910
OVER TP
RS-232 IR
Tx Rx Tx RxG
1
LR
1
LR
3
LR
3
LR
5
LR
2
LR
4
LR
2
LR
4
LR
6
LR
SIG LINK
OUT
5B 6B 6
RS-232 IR
Tx Rx Tx Rx
XTP
S/PDIF
OUT
DTP
HDBT
G
RS-232 IR
Tx Rx Tx RxG
OVER TP
XTP
DTP
HDBT
78
RS-232 IR
Tx Rx Tx Rx
XTP
DTP
HDBT
G
RS-232 IR
Tx Rx Tx RxG
OVER TP
Tx Rx RTSCTS GTxRxG Tx Rx G
LAN 2
LAN 1
LAN 3
R
CONTROL
1234G
DIGITAL I/OCOM 3COM 2COM 1
SSGG
1
1
2
2
C34C
-S G+S+V
PWR OUT = 6W
IR/SERIAL eBUSRELAYS
SIG LINK
IN
SIG LINK
IN
SIG LINK
IN
SIG LINK
IN
SIG LINK
OUT
SIG LINK
OUT
SIG LINK
OUT
Tx Rx G
RESET
REMOTE
LAN
AMP OUTPUT
CLASS 2 WIRING
1
DTP CrossPoint IPCP SA
DTP CrossPoint IPCP MA
1
L
R
48/
AMP OUTPUT
CLASS 2 WIRING
50-60 Hz
100-240V ~
3.0 A MAX
GHIJK
L
M
N
Figure 6. Audio Input and Output Connections and Indications, 10x8 Matrix
50-60 Hz
100-240V ~ 1.6 A MAX
12
123456
3A 4A
4B
RS-232 IR
RS-232 IR
Tx Rx Tx RxG
Tx Rx Tx Rx
XTP
RESET
DTP
XTP
DTP
XTP
DTP
XTP
DTP
HDBT
HDBT
G
7
8
DTP CROSSPOINT 84 4K
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
OVER TP
OVER TP
INPUTS
OUTPUTS
3B
Tx Rx G
REMOTE
SIG LINK
OUT
SIG LINK
OUT
SIG LINK
IN
SIG LINK
IN
+48V
MIC/LINE
1
1
3
2
4
2
3
4
LINK
EXP
AUDIO OUTPUTS
AUDIO INPUTS
DMP EXPANSION
1
LR
1
LR
3
LR
3
LR
5
LR
2
LR
4
LR
2
LR
4
LR
6
LR
4
S/PDIF
OUT
CLASS 2 WIRING
R
CONTROL
Tx Rx RTSCTS G
12
12
SGSG
C
34C+V
PWR OUT = 6W
+V D-S+S
Tx Rx G Tx Rx G1234G
COM 1 COM 3COM 2 DIGITAL I/O
LAN 1
LAN 2 LAN 3
IR/SERIAL RELAYS DIGITAL I/O
AMP OUTPUT
1
DTP CrossPoint IPCP MA
AMP OUTPUT
CLASS 2 WIRING
DTP CrossPoint IPCP SA
1
L
R
48/
KM
L
N I
G H J
Figure 7. Audio Input and Output Connections and Indications, 8x4 matrix
For inputs and outputs on captive screw connectors (see figure 6 and figure 7,
G
,
H
, and
J
),
the connectors are included with the switcher, but you must supply the audio cable.
G
Audio inputs 1 through 6 — Connect balanced or unbalanced stereo audio
LR
inputs to these 5-pole, 3.5 mm captive screw connectors (see Analog audio
input connectors on page 21 to wire the connectors).
H
Mic/Line inputs 1 through 4 — Connect microphones or other mono audio
inputs to these 3-pole, 3.5 mm captive screw connectors (see Mic/Line input
connectors on page 22 to wire the connectors).
I
+48 V (phantom power) LEDs — These LEDs light to indicate that +48 V
+48V
1
phantom power is applied to the associated mic/line inputs.
J
Audio outputs — Connect audio devices such as an audio amplifier or
LR
powered speakers to these 4 or 2, 5-pole, 3.5 mm captive screw connectors.
These connectors output unamplified, line level audio, whether it is tied from
an analog input or de-embedded from an HDMI input (see Analog audio output
connectors on page 22 to wire the connectors).
1
L
R
4
CLASS 2 WIRING
8/
K
Amp output 1 (stereo audio model) — Connect unpowered, 4-ohm or
8-ohm speakers to this 4-pole 5 mm captive screw connector to play
the amplified stereo audio from audio output 1.
L
Amp output 1 (mono audio model) — Connect unpowered, high
1
CLASS 2 WIRING
impedence speakers to this 2-pole captive screw connector to play the
amplified mono audio from audio output 1.
ATTENTION:
• Ensure the rated input voltage of the speakers matches the rated output
voltage of the switcher.
• Assurez-vous que la tension nominale d’entrée des enceintes soit compatible
avec la tension nominale de sortie du sélecteur.