Extron electronics DTP CrossPoint 4K Series - Operation

DTP CrossPoint 4K Series Matrix Switchers • Installation 17
Control Connections
Tx Rx RTSCTS GTxRxG Tx Rx G
Tx Rx G
LAN 2
LAN 1
LAN 3
DTP CROSSPOINT 108 4K
R
CONTROL
1234G
DIGITAL I/OCOM 3COM 2COM 1
SSGG
1
1
2
2
C34C
-S G+S+V
PWR OUT = 6W
IR/SERIAL eBUSRELAYS
REMOTE
LAN
EXP
+48V
MIC/LINE
1
1
3
2
4
2
3
4
LINK
AUDIO OUTPUTS
AMP OUTPUT
AUDIO INPUTS
DMP EXPANSION
1
LR
1
LR
3
LR
3
LR
5
LR
2
LR
4
LR
2
LR
4
LR
6
LR
1
CLASS 2 WIRING
70V
RESET
RS-232 IR
Tx Rx Tx RxG
XTP
DTP
XTP
DTP
123457 86
OVER TP
INPUTS INPUTS
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
XTP
DTP
XTP
DTP
91
0
OVER TP
RS-232 IR
Tx Rx Tx RxG
SIG LINK
IN
SIG LINK
IN
SIG LINK
IN
SIG LINK
IN
50-60 Hz
100-240V ~
3.0 A MAX
1 2 3 4 5A 6A
XTP
DTP
HDBT
OUTPUTS
SIG LINK
OUT
5B 6B 6
RS-232 IR
Tx Rx Tx Rx
XTP
S/PDIF
OUT
DTP
HDBT
G
RS-232 IR
Tx Rx Tx RxG
OVER TP
XTP
DTP
HDBT
78
RS-232 IR
Tx Rx Tx Rx
XTP
DTP
HDBT
G
RS-232 IR
Tx Rx Tx RxG
OVER TP
SIG LINK
OUT
SIG LINK
OUT
SIG LINK
OUT
R QS
Figure 10. Control Connections, 10x8 Matrix
50-60 Hz
100-240V ~ 1.6 A MAX
+48V
MIC/LINE
1
1
3
2
4
2
3
4
EXP
DTP CROSSPOINT 84 4K
AUDIO OUTPUT
S
AUDIO INPUT
S
DMP EXPANSION
1
LR
1
R
3
LR
3
L
L
R
5
LR
2
LR
4
LR
2
LR
4
LR
6
LR
AMP OUTPUT
CLASS 2 WIRING
1
100V
12
123456
3A 4A
4B
RS-232 IR
RS-232 IR
Tx Rx Tx RxG
Tx Rx Tx Rx
XTP
DTP
XTP
DTP
XTP
DTP
XTP
DTP
HDBT
HDBT
G
7
8
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
OVER TP
OVER TP
INPUTS
OUTPUTS
3B
SIG LINK
OUT
SIG LINK
OUT
SIG LINK
IN
SIG LINK
IN
4
S/PDIF
OUT
R
CONTROL
Tx Rx RTSCTSG
12
12
SGSG
C
34C+V
PWR OUT = 6W
+V D-S+S
Tx Rx G Tx Rx G1234G
COM 1 COM 3COM 2 DIGITAL I/O
LAN 1
LAN 3
LAN 2
IR/SERIAL RELAY S DIGITAL I/O
Tx Rx G
REMOTE
LAN
RESET
RQS
Figure 11. Control Connections, 4x8 Matrix
NOTE: Figure 10 and figure 11 show features of all models. Actual models have either a
LAN port (
Q
) or a control processor (
R
), but not both.
Q
LAN port (non-IPCP model) — If desired, for IP control of the switcher,
LAN
connect the matrix switcher to a PC or to an Ethernet LAN via this RJ-45
connector (see TP connectors on page 19 to wire the connector). You can
use a PC to control the networked switcher from anywhere in the world using
any of the following methods:
• SIS commands (see Using the Command and Response Tables on page 67)
• Extron Product Configuration Software (see Product Configuration Software on
page 88)
• DSP Configurator program (see DSP Configurator Program on page 96)
• Built-in HTML pages (see HTML Pages on page 152)
Act (yellow) LED — The Act LED indicates transmission of data packets on the RJ-45
connector. This LED should blink as the switcher communicates.
Link (green) LED — The Link LED indicates that the switcher is properly connected to
an Ethernet LAN. This LED should light steadily.
R
IPCP Pro 350 control processor (IPCP models only) — The IPCP models include
a built-in IPCP control processor that can control and monitor a variety of external
devices. The IPCP offers RS-232 and IR-based control, relays, and digital I/O controls.
It also offers Ethernet-based control for some devices. Controllable devices can include:
• Projectors or other displays
• Source devices
• Switchers
• Lights
• Projector lifts
• Screen motors
S
Remote port — Plug a serial RS-232 device into the matrix
Tx Rx G
REMOTE
LAN
switcher via this 3.5 mm, 3-pole captive screw connector for remote
control of the switcher (see Serial and IR port connectors on
page 23 to wire the connector).