Extron electronics DTP CrossPoint 4K Series - Rear Panel Cabling and Features

DTP CrossPoint 4K Series Matrix Switchers • Installation 11
Rear Panel Cabling and Features
The various models have different numbers of inuts and outputs. The non-IPCP, SA, and
MA models have similar features, with differences in the control connections and Amplified
Output block only. Figure 2 shows the rear panel of a composite DTP CrossPoint 108 4K
model, featuring elements of different models. Figure 3 shows only the Amplified Output
block portion of the MA models.
50-60 Hz
100-240V ~
3.0 A MAX
1
L
R
1 2 3 4 5A 6A
XTP
Tx Rx RTSCTS GTxRxG Tx Rx G
RS-232 IR
Tx Rx Tx RxG
Tx Rx G
RESET
XTP
DTP
XTP
DTP
EXP
+48V
MIC/LINE
1
1
3
2
4
2
3
4
LINK
LAN 2
LAN 1
LAN 3
DTP
HDBT
1234 57 86
DTP CROSSPOINT 108 4K
4
CLASS 2 WIRING
8/
R
OVER TP
SIG LINK
IN
SIG LINK
IN
AUDIO INPUTS
AUDIO OUTPUTS
AMP OUTPUT
CONTROL
1234G
DIGITAL I/OCOM 3COM 2COM 1
S
DMP EXPANSION
SGG
1
1
2
2
C34C
INPUTS INPUTS
-S G+S+V
PWR OUT = 6W
OUTPUTS
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
XTP
DTP
XTP
DTP
91
0
OVER TP
SIG LINK
IN
SIG LINK
IN
RS-232 IR
Tx Rx Tx RxG
1
LR
1
LR
3
LR
3
LR
5
LR
2
LR
4
LR
2
LR
4
LR
6
LR
IR/SERIAL eBUSRELAYS
REMOTE
LAN
SIG LINK
OUT
SIG LINK
OUT
5B 6B 6
RS-232 IR
Tx Rx Tx Rx
XTP
S/PDIF
OUT
DTP
HDBT
G
RS-232 IR
Tx Rx Tx RxG
OVER TP
XTP
DTP
HDBT
SIG LINK
OUT
SIG LINK
OUT
78
RS-232 IR
Tx Rx Tx Rx
XTP
DTP
HDBT
G
RS-232 IR
Tx Rx Tx RxG
OVER TP
Figure 2. DTP CrossPoint 108 4K IPCP SA Matrix Switcher Rear Panel (Showing
non-IPCP LAN Port, IPCP, and SA [Stereo Audio] Components)
NOTE: Figure 2 is composite that shows features of all models. Actual models can
have either a remote LAN port or an IPCP Pro 350 module, but not both. Models with
amplified output have either the 4 pole stereo connector shown in figure 2 or the 2 pole
mono connector shown in figure 3.
1
CLASS 2 WIRING
70V
Figure 3. MA (Mono Audio) Amplified Output Block
ATTENTION:
• Use electrostatic discharge (ESD) precautions (be electrically grounded) when
making connections. Electrostatic discharge can damage equipment, even if you
cannot feel, see, or hear it.
• Prenez des précautions contre les décharges électrostatiques (soyez
électriquement relié à la terre) lorsque vous effectuez des connexions.
• Remove system power before making all connections.
• Débranchez l’alimentation du système avant de faire n’importe quelle connexion.
For connector details, see the following sections:
• Video and TP Input and Output Connections and Switches (see the next page)
• Audio Input and Output Connections (see page 15)
• Serial and IR Insertion Connections (see page 16)
• Control Connections (see page 17)
• Switcher Reset (see page 18)
• Power (see page 18)