Extron electronics DTP CrossPoint 4K Series - Page 82

Command and Response Table for Matrix Switcher Commands (continued)
DTP CrossPoint 4K Series Matrix Switchers • Programming Guide 74
Command Function
SIS Command
(Host to Unit)
Response
(Unit to Host)
Additional description
Audio input format
View detected digital input audio
format
E
40*
X$
STAT
} X1@]
40Stat
X$
*
X1@]
Format detected on input
X$
is
X1@
.
Verbose mode 2 or 3 response.
Input reports as an HDCP-authorized device
HDCP authorized device on
E
E
X$
*1HDCP
}
HdcpE
X$
*1
]
Set the input as HDCP authorized.
HDCP authorized device off
E
E
X$
*0HDCP
}
HdcpE
X$
*0
]
Set the input as not HDCP authorized.
View HDCP authorized status
E
E
X$
HDCP
} X1#]
Show HDCP authorized device status.
HDMI HDCP output settings
Set output HDCP mode to auto
E
S
X%
*0HDCP
}
HdcpS
X%
*0
]
Set output
X%
HDCP to auto.
Set output HDCP mode to follow (DVI)
E
S
X%
*2HDCP
}
HdcpS
X%
*2
]
Set output
X%
HDCP to follow (DVI).
Set output HDCP mode to on
E
S
X%
*1HDCP
}
HdcpS
X%
*1
]
Set output
X%
HDCP to always encrypted.
Set output HDCP mode to on (DVI)
E
S
X%
*3HDCP
}
HdcpS
X%
*3
]
Set output
X%
HDCP to on (DVI).
View output HDCP mode
E
S
X%
HDCP
} X1$]
HDCP notification
Set green screen
E
N
X&
*1HDCP
}
HdcpN
X&
*1
]
Set black screen
E
N
X&
*0HDCP
}
HdcpN
X&
*0
]
View HDCP notification
E
N
X&
HDCP
} X1%]
HDCP status
View input HDCP status
E
I
X$
HDCP
} X1^]
HdcpI
X$
*
X1^]
for verbose mode 2 and 3.
View HDCP status of all inputs
E
IHDCP
} X1^
1
X1^
2
X1^
3
...
X1^
n
]
10 or 8 (n)
X1^
s, starting at input 1.
View output HDCP status
E
O
X&
HDCP
} X1&]
HdcpO
X&
*
X1&]
for verbose mode 2 and 3.
View HDCP status of all outputs
E
OHDCP
} X1&
1
X1&
2
X1&
3
...
X1&
n
]
10, 8, 6, or 4 (n)
X1&
s (with As and Bs),
starting at output 1.
Example (DTP CrossPoint 108):
E
OHDCP
}
0
1
2
2
3
3
4
4
1
5A
2
5B
3
6A
0
6B
1
7
2
8
]
Input and output format
View input format
X$
*\
X1*]
Ityp
X$
*
X1*]
for verbose mode 2 and 3.
Set output format
EX&
*
X1*
VTPO
}
Vtpo
X&
*
X1*]
View output format
EX&
VTPO
} X1*]
Output video bit depth
Set bit depth
EX%
*
X1(
BITD
}
Bitd
X%
*
X1(]
View bit depth
EX%
BITD
} X1(]
NOTE: X$ = Input number 01 – the highest numbered input for your model
X% = Output number 01 – the highest numbered output for your model
X& = Output number (with A and B) See X& definition on page 68 for numbers by matrix size.
X1@ = Detected input audio format 0 = None 1 = Analog 2 = 2-channel PCM 3 = Bitstream
X1# = HDCP authorized device status 0 = Off 1 = On (default)
X1$ = HDCP output mode 0 = Auto (follow the input) (default) 2 = Follow input with continuous DVI trials
1 = On (always encrypt HDMI outputs) 3 = Always encrypt HDMI outputs, continuous DVI trials
X1% = HDCP notification 0 = Black screen 1 = Green screen (default)
X1^ = HDCP status (for inputs) 0 = No source device connected 2 = Connected source is not HDCP-compliant
1 = Connected source is HDCP-compliant
X1& = HDCP status (for outputs) 0 = No monitor connected 1 = Monitor connected, does not support HDCP
2 = Monitor connected, supports HDCP ,the video signal is not encrypted
3 = Monitor connected, supports HDCP, the video signal is encrypted
X1* = Video format 0 (input) = No signal detected
0 (output) = Auto (HDMI RGB Full to CEA sink or DVI to non-CEA sink)
1 = DVI (RGB 444, no audio, no InfoFrames)
2 = HDMI RGB Full (RGB 444, 000 - 255 audio, InfoFrames)
3 = HDMI RGB Limited (RGB 444, 016 - 255 audio, InfoFrames)
4 = HDMI YUV Full (RGB 444, 000 - 255 audio, InfoFrames)
5 = HDMI YUV Limited (RGB 444, 016 - 255 audio, InfoFrames)
6 = HDMI YUV Full (RGB 422, 000 - 255 audio, InfoFrames)
7 = HDMI YUV Limited (RGB 422, 016 - 255 audio, InfoFrames)
X1( = Output video bit depth 0 = Auto (default) 1 = 8-bit