5500A
Operator Manual
INDEX-2
Bus Setup Procedure, 5-7
—C—
Cable Connection Instructions, 4-11
Cable Connections for Testing a 40 Series Watts
Function, 4-59
Cable Connections for Testing a 50 Series
Thermometer, 4-62
Cable Connections for Testing an 80 Series Current
Function, 4-55
Cable Connections for Testing an 80 Series General
Functions, 4-53
Cable Connections for Testing an 80 Series High
Amps Function, 4-57
Cable recommendations, 4-9
Cables, 4-52
Calculating power uncertainty, 1-25
Calibrating an
80 Series DMM, 4-52
Fluke 51 Thermometer, 4-61
Calibrating the Meter, 4-57
Calibrating the Thermocouple, 4-63
Calibration Check, Performing a, 7-6
CALIBRATION Switch, 3-10
Calibration Switch, Enabled Commands, 5-29
Capacitance Accuracy, 7-17
Capacitance Output Setting, 4-33
Caution, 4-63, 7-6
CAUTION, 2-3, 2-7, 4-6, 4-9, 4-18, 4-19, 4-24, 4-26,
4-28, 4-30, 7-4
CE key, 3-6
CFREQ? remote command, 6-12
Changing between remote and local operation, 5-21
Character Processing, Incoming, 5-33
CHASSIS GROUND Binding Post, 3-11
Checking 5500A status, 5-35
Cleaning the Air Filter, 7-4
Cleaning, General, 7-6
CLS remote command, 6-12
Command Summary by Function, 6-3
Command syntax information, 5-31
Commands
Alphabetical List, 6-8
Calibration Switch Enabled, 5-29
Common, 5-26
Compound, 5-28
Coupled, 5-28
Device-Dependent, 5-25
IEEE-488 Only, 5-30
Overlapped, 5-29
Query, 5-26
RS-232 Only, 5-29
Sequential, 5-29
Summary by Function, Table of, 6-3
Types of, 5-25
Using, 5-25
Commands for RS-232 Only, 5-29
Common Commands, 5-26, 6-4
Compound Commands, 5-28
Connecting the 5725A Amplifier, 2-7
Connecting the Calibrator to a UUT, 4-9
Control Display, 3-4
Cooling Considerations, 2-7
Coupled Commands, 5-28
CUR_POST remote command, 6-12
CUR_POST? remote command, 6-12
Current
Limit setting, 4-51
Setting AC Output, 4-22
Setting DC output, 4-21
—D—
DC Current Amplitude Accuracy, 7-9
DC Current Output, 4-21
DC Offset, Entering of, 4-46
DC Power Amplitude Accuracy (AUX), 7-19
DC Power Amplitude Accuracy (NORMAL), 7-19
DC Power Output, 4-24
DC Voltage Amplitude Accuracy (AUX), 7-8
DC Voltage Amplitude Accuracy (NORMAL), 7-7
DC Voltage Offset Accuracy, 7-26
DC Voltage Output, Setting of, 4-18
DC Voltage, Dual voltage setting, 4-28
DC_OFFSET remote command, 6-13
DC_OFFSET? remote command, 6-13
Device-Dependent Commands, 5-25
Display
Control, 3-4
Output, 3-4
Displaying the Output Error, 4-50
DIVIDE key, 3-7
Divide, Using Multiply and Divide, 4-50
DPF remote command, 6-13
DPF? remote command, 6-13
Dual AC Voltage Output, 4-30
Dual DC Voltage Output, 4-28
DUTY remote command, 6-14
DUTY? remote command, 6-14
—E—
EARTH
When to Use, 4-10
EARTH Connection, 4-52
EARTH key, 3-5
EARTH remote command, 6-14
EARTH? remote command, 6-14
Edge Function, 8-19, 8-72
Specifications, 8-7, 8-61
To Next Page
Loading...
