Fluke 5700A Series II User Manual

5700A/5720A Series II
Operators Manual
iv
5-10. Extra Space Characters..................................................................... 5-9
5-11. Terminators....................................................................................... 5-9
5-12. Incoming Character Processing........................................................ 5-9
5-13. Response Message Syntax................................................................ 5-10
5-14. Input Buffer Operation.......................................................................... 5-10
5-15. Commands ............................................................................................ 5-10
5-16. Multiple Commands ......................................................................... 5-11
5-17. Coupled Commands ......................................................................... 5-11
5-18. Sequential and Overlapped Commands............................................ 5-12
5-19. Commands Ignored When Not in Remote ....................................... 5-12
5-20. Commands that Require the Calibration Switch to be Set ............... 5-12
5-21. Long Term Commands..................................................................... 5-12
5-22. Local-to-Remote State Transitions ....................................................... 5-43
5-23. Checking the Calibrator’s Status .......................................................... 5-45
5-24. Serial Poll Status Byte ...................................................................... 5-47
5-25. Service Request Line (SRQ) ........................................................ 5-48
5-26. Service Request Enable Register.................................................. 5-48
5-27. Loading the SRE .......................................................................... 5-48
5-28. Event Status Register........................................................................ 5-49
5-29. Bit Assignments for the ESR and ESE......................................... 5-49
5-30. Reading the ESR and ESE ........................................................... 5-50
5-31. Loading the ESE .......................................................................... 5-50
5-32. Instrument Status Register................................................................ 5-51
5-33. Instrument Status Change Register................................................... 5-51
5-34. Instrument Status Change Enable Register ...................................... 5-51
5-35. Bit Assignments for the ISR, ISCR, and ISCE ............................ 5-51
5-36. Reading the ISR, ISCR, or ISCE ................................................. 5-52
5-37. Loading the ISCE......................................................................... 5-52
5-38. Fault Queue ...................................................................................... 5-53
5-39. IEEE-488 Interface Configuration........................................................ 5-54
5-40. Bus Communication Overview............................................................. 5-55
5-41. Definition: Queries and Commands ................................................. 5-56
5-42. Functional Elements Of Commands................................................. 5-56
5-43. Interface Messages ........................................................................... 5-58
5-44. The IEEE-488 Connector...................................................................... 5-60
5-45. Remote Program Examples................................................................... 5-61
5-46. Printing Main Output Calibration Shift Results ............................... 5-61
5-47. Verifying a Meter ............................................................................. 5-62
5-48. Remote Calibration........................................................................... 5-62
5-49. DC Zeros ...................................................................................... 5-62
5-50. Calibration.................................................................................... 5-63
5-51. Calibration Check ........................................................................ 5-64
5-52. Wideband AC Module (Option 5700A-03) Gain Calibration...... 5-65
5-53. Using *OPC?, *OPC, and *WAI ..................................................... 5-66
5-54. Writing an SRQ and Fault Handler .................................................. 5-67
5-55. Emulating a Fluke 5100B or 5200A Calibrator.................................... 5-68
5-56. Entering Emulation Mode ................................................................ 5-68
5-57. Exiting Emulation Mode .................................................................. 5-69
5-58. The 5720’s Display During Emulation............................................. 5-69
5-59. 5100B Emulation .................................................................................. 5-69
5-60. Local-to-Remote Transitions............................................................ 5-69
5-61. Current Output Location................................................................... 5-70
5-62. Differences in the 5700A/5720A Series II and 5100B
Ohms Function.................................................................................. 5-70
5-63. Ohms Remote Program Modifications for 5100B Emulation .......... 5-71

Fluke 5700A Series II Specifications

General

Type	Multifunction Calibrator
Operating Temperature	0 °C to 50 °C
Storage Temperature	-20 °C to 70 °C
Voltage Range	0 to 1100 V
DC Voltage Range	10 μV to 1100 V
Frequency Range	1 MHz
Humidity	non-condensing
Power Requirements	100 V to 240 V