5700A/5720A Series II
Operators Manual
2
Ampl/Freq key, 3-6
Amplifiers. See Auxiliary Amplifier
Applications, sample, 4-51
Arrow key, 3-6
Arrow keys, 4-38
AUX CURRENT OUTPUT Binding Post, 3-10
Auxiliary Amplifiers, 1-5, 2-8, 4-36, 8-5
5725A Amplifier, 1-6
—B—
Backup Battery, 4-9
Binding, 4-13
Binding Post
Chassis Ground, 3-14
Current Guard, 3-12
GND, 3-10
OUTPUT, 3-12
OUTPUT, 3-10
Rear panel, 3-12
SENSE, 3-12
SENSE, 3-10
Voltage Guard, 3-12
Voltage Guard, 3-10
Binding Post Selection, 2-8
Boost key, 3-6
BOOST key, 4-36
BTYPE remote command, 5-17
BTYPE? remote command, 5-18
Bus Communication Overview, 5-55
—C—
Cable Connection Instructions, 4-16
Cable Recommendations, 4-13
CAL_ADJ remote command, 5-18
CAL_CHK remote command, 5-18
CAL_CLST? remote command, 5-18
CAL_CONF remote command, 5-19
CAL_CONF? remote command, 5-19
CAL_CONST? remote command, 5-19
CAL_DATE? remote command, 5-19
CAL_DAYS? remote command, 5-19
CAL_INTV remote command, 5-20
CAL_INTV? remote command, 5-20
CAL_PR remote command, 5-20
CAL_REF remote command, 5-20
CAL_RNG remote command, 5-21
CAL_RPT? remote command, 5-21
CAL_SHIFT? remote command, 5-22
CAL_SLST? remote command, 5-23
CAL_STORE remote command, 5-23
CAL_TEMP remote command, 5-24
CAL_TEMP? remote command, 5-24
CAL_WBFLAT remote command, 5-24
CAL_WBGAIN remote command, 5-25
CAL_ZERO remote command, 5-25
Calculation, dBm, 4-25, 4-33
Calibrating 70 Series DMM
Cables, 4-52
Calibrating 70 Series DMM
Guarding, 4-52
Calibrating a 70 Series DMM, 4-51
Calibrating the Meter, 4-54
Testing the Meter, 4-53
Calibrating a70 Series DMM
Sensing, 4-52
Calibrating an 8840A Series Digital
Multimeter, 4-56
Calibrating an 8840A Series DMM
A/D Calibration, 4-59
Basic Calibration Procedure, 4-58
Calibration Setup Procedure, 4-58
Guarding, 4-56
High Frequency AC Calibration, 4-62
Offset and Gain Calibration, 4-60
Sensing, 4-58
Calibrating the 5700A/5720A Series II
Calibration Check, 1-11
Calibration Process, 1-10
Calibration Reports, 1-10
Establishment of Traceability, 1-10
Performance history, developing, 1-11
Range Calibration, 1-11
Calibrating the 5700A/5720A Series II, 1-8
Calibrating to external standards, 7-6
calibration procedure, 7-8
calibration requirements, 7-7
Calibration, 7-6
DC Zeroes, 1-11
range, 7-14
Wideband AC Module (Option 5700A-03), 7-18
Calibration Check, 7-21
CALIBRATION Switch, 3-13
CHASSIS GROUND Binding Post, 3-14
Checking the Calibrator’s Uncertainty
Specification, 4-38
Cleaning
air filter, 7-4
exterior, 7-6
Clear Entry (CE) key, 3-8
Clearance, for installation, 2-4
CLOCK remote command, 5-25
Clock/Calendar, setting, 4-9
CLOCK? remote command, 5-25
Commands. See Remote Commands
Compensation circuitry, two-wire lead
drop, 4-32
Components of the 5700A/5720A Series II, 1-8
Configuration Data, 4-11
Connecting the Calibrator to a UUT, 4-13
Connecting to Line Power, 2-8
Connections, alternative for UUT, 3-12
To Next Page
Loading...
